Huawei S5700 Series Скачать руководство пользователя страница 298 | Manualshive

Страница: 298 / 415

background image

Procedure

l

Run the

display nqa results

[

test-instance

admin-name

test-name

] command to view the

test results on the NQA client.

l

Run the

display nqa-server

command to view the information about the NQA server.

----End

Example

Run the

display nqa results

command. If the test is successful, the following is displayed.

<Quidway>

display nqa results

NQA entry(admin, udp) :testflag is inactive ,testtype is udp
1 . Test 1 result The test is finished
Send operation times: 3 Receive response times: 3
Completion:success RTD OverThresholds number: 0
Attempts number:1 Drop operation number:0
Disconnect operation number:0 Operation timeout number:0
System busy operation number:0 Connection fail number:0
Operation sequence errors number:0 RTT Stats errors number:0
Destination ip address:10.2.1.2
Min/Max/Average Completion Time: 32/109/67
Sum/Square-Sum Completion Time: 203/16749
Last Good Probe Time: 2006-8-5 16:9:21.6
Lost packet ratio: 0 %

Run the

display nqa-server

command. If the status of the NQA server is displayed, it means

that the configuration succeeds.

<Quidway>

display nqa-server

NQA Server Max: 100 NQA Server Num: 1
NQA Concurrent TCP Server : 0 NQA Concurrent UDP Server: 1

nqa-server udpecho 10.112.58.3 3000 ACTIVE

6.14 Configuring the Jitter Test

This section describes how to configure a jitter test to check jitter on the network. You can
perform a jitter test only when both the client and the server are Huawei devices.

6.14.1 Establishing the Configuration Task

Before configuring a jitter test, familiarize yourself with the applicable environment, complete
the pre-configuration tasks, and obtain the required data. This can help you complete the
configuration task quickly and accurately.

Applicable Environment

The jitter time refers to the interval for sending two adjacent packets minus the interval for
receiving the two packets.

The process of a Jitter test is as follows:

1.

The source sends a packet to the destination at a specified interval.

2.

After receiving the packet, the destination adds a timestamp to the packet and returns them
to the source.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management

6 NQA Configuration

Issue 01 (2011-10-26)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

287

«
...
296
297
298
299
300
...
»

Содержание S5700 Series
































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S5700 Series

Бренд: D-Link Страницы: 11

Бренд: D-Link Страницы: 8

AirPlus DWL-810

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 84

Бренд: D-Link Страницы: 2

UR5i v2 Libratum

Бренд: B+B SmartWorx Страницы: 8

Бренд: B+B SmartWorx Страницы: 8

Бренд: Selta Страницы: 83

GSM7224v2 - Layer 2 Managed Gigabit Switch

Бренд: NETGEAR Страницы: 3

802.11a/b/g SDIO WiFi Module SDM3100

Бренд: Abocom Страницы: 14

Бренд: Watchguard Страницы: 21

Modular Fast Fiber Switch Converter MT-RJ

Бренд: Lindy Страницы: 3

Бренд: Supero Страницы: 54

Бренд: Axis Страницы: 64

Бренд: SHOWTEC Страницы: 15

Бренд: E-Lins Страницы: 10

Бренд: Yeti Страницы: 29

Бренд: NAUTICAST Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды