Huawei S5700 Series Скачать руководство пользователя страница 63

Страница: 63 / 415

TLV Types Supported by the S5700

Besides the mandatory TLVs Chassis ID TLV, Port ID TLV, Time to Live TLV, and End of
LDPDU, the S5700 supports the following optional TLVs.

Basic TLV

Type

Description

Management Address TLV

Management IP address

Port Description TLV

Interface description

System Capabilities TLV

Capacities of the local device, including:

other: other capability

repeater

bridge

wlanAccessPoint: wireless access point

router

telephone: wireless device

docsisCableDevice: management
station

stationOnly: station

System Description TLV

Device description

System Name TLV

Device name

Organizationally Specific TLV defined in 802.1

Type

Description

Port VLAN TLV

VLAN ID of an interface

Port protocol VLAN TLV

Protocol VLAN ID of an interface

VLAN Name TLV

VLAN name

Protocol identity TLV

Protocol types supported by an interface

Organizationally Specific TLV defined in 802.3

Type

Description

Link Aggregation TLV

Whether a port supports link aggregation
and is enabled with link aggregation

MAC/PHY Configuration/Status TLV

Rate and duplex status of a port, whether
auto-negotiation is supported, and whether
auto-negotiation is enabled

Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management

2 LLDP Configuration

Issue 01 (2011-10-26)

Huawei Proprietary and Confidential

Содержание S5700 Series
































































































































































































































































































































































































































Результаты поиска

Содержание S5700 Series

Отзывы:

Похожие инструкции для S5700 Series

Бренды по названию

Популярные бренды

Huawei S5700 Series, Конфигурационное руководство - Управление сетью

Результаты поиска

Содержание S5700 Series

Отзывы:

Похожие инструкции для S5700 Series

Бренды по названию

Популярные бренды