Huawei S5700 Series Скачать руководство пользователя страница 293

Страница: 293 / 415

Context

Do as follows on the NQA client (TCP client):

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

nqa

test-instance

admin-name

test-name

An NQA test instance is created and the test instance view is displayed.

Step 3

Run:

test-type

tcp

The test type is set to TCP.

Step 4

Run:

destination-address

ipv4

ip-address

The destination IP address is configured.

Step 5

To configure the destination port number, run the

destination-port

port-number

command.

Step 6

(Optional) Perform the following as required to configure other parameters for the TCP test ( For
detailed parameter configurations, see the chapter

Configuring Universal NQA Test

Parameters

To configure the VPN instance to be tested, run the

vpn-instance

vpn-instance-name

command.

NOTE

Only S5700EI and S5700HI support the

vpn-instance

command.

To configure the source IP address, run the

source-address

ipv4

ip-address

command.

To configure the source port number, run the

source-port

port-number

command.

To configure the interval for sending test packets, run the

interval

seconds

interval

command.

To configure the percentage of the failed NQA tests, run the

fail-percent

percent

command.

To configure the NQA test packets to be sent without searching the routing table, run the

sendpacket passroute

command.

Step 7

Run:

start

The NQA test is started.

Select the start mode as required because the

start

command has several forms.

To perform the NQA test immediately, run the

start

now

[

end

{

[

yyyy

]

delay

{

seconds

second

} |

lifetime

{

seconds

second

} } ]

command.
The test instance is started immediately.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management

6 NQA Configuration

Issue 01 (2011-10-26)

Huawei Proprietary and Confidential

282

Содержание S5700 Series
































































































































































































































































































































































































































Результаты поиска

Содержание S5700 Series

Отзывы:

Huawei S5700 Series, Конфигурационное руководство - Управление сетью, Страница: 293 / 415

Результаты поиска

Содержание S5700 Series

Отзывы: