manualshive.com logo in svg

Huawei S5700 Series, Конфигурационное руководство - Управление сетью, Страница: 315 / 415

Поделиться
Скачать
Huawei S5700 Series Скачать руководство пользователя страница 315

Procedure

Step 1

Run:

system-view

The system view is displayed.

Step 2

Run:

nqa

 

test-instance

 

admin-name

 

test-name

An NQA test instance is created and the test instance view is displayed.

Step 3

Run:

test-type

 

icmpjitter

The type of the test instance is configured as ICMP jitter.

Step 4

Run:

destination-address

 

ipv4

 

ip-address

The destination IP address is configured.

Step 5

(Optional) Run the following commands to configure other parameters for the jitter test:

l

Run:

icmp-jitter-mode

 { 

icmp-echo

 | 

icmp-timestamp

 }

The mode of the ICMP jitter test is configured.

l

Run:

vpn-instance

 

vpn-instance-name

The VPN instance to be tested is configured.

NOTE

Only the S5700HI and S5706LI support this parameter.

l

Run:

probe-count

 

number

The number of test probes to be sent each time is set.

l

Run:

jitter-packetnum

 

number

The number of test packets to be sent during each test is set.

NOTE

The 

probe-count

 command is used to configure the number of times for the jitter test and the 

jitter-

packetnum

 command is used to configure the number of test packets to be sent during each test. In

actual configuration, the product of the number of times for the jitter test multiplied by the number of
test packets must be less than 3000.

l

Run:

interval

 { 

milliseconds

 

interval

 }

The interval for sending test packets is set.
The shorter the interval is, the sooner the test is complete. However, delays arise from sending
and receiving test packets on the processor. Therefore, if the interval for sending test packets
is set to a small value, a relatively greater error may occur in the statistics of the jitter test.

l

Run:

fail-percent

 

percent

Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management

6 NQA Configuration

Issue 01 (2011-10-26)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

304

Содержание S5700 Series
































































































































































































































































































































































































































Отзывы:

Нет отзывов