Huawei S5700 Series Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 415

background image

Step 4

Run:

set constant-ifindex subinterface

{

dense-mode

|

sparse-mode

}

The memory distribution mode for the sub-interface index is set.

When a sub-interface is created, the system generates an index image file for the sub-interface
in the memory in a specified mode. You may use various sub-interface numbering modes, such
as the continuous mode or the discontinuous mode. In real-world situations, one of the following
distribution modes can be used as needed:

l

Sparse mode: applies to discontinuous sub-interface numbering.

l

Dense mode: applies to continuous sub-interface numbering.

----End

1.2.7 Checking the Configuration

After SNMPv1 functions are configured, you can view the SNMPv1 configurations.

Prerequisite

The configurations of basic SNMPv1 functions are complete.

Procedure

l

Run the

display snmp-agent community

command to check the configured community

name.

l

Run the

display snmp-agent sys-info

version

command to check the enabled SNMP

version.

l

Run the

display acl

acl-number

command to check the rules in the specified ACL.

l

Run the

display snmp-agent mib-view

command to check the MIB view.

l

Run the

display snmp-agent sys-info

contact

command to check the equipment

administrator's contact information.

l

Run the

display snmp-agent sys-info

location

command to check the location of the

device.

l

Run the

display snmp-agent target-host

command to check the information about the

target host.

l

Run the

display snmp-agent extend error-code status

command to check whether the

SNMP extended error code feature is enabled.

l

Run the

display constant-ifindex configuration

command to check the constant interface

index function and relevant configuration information.

----End

1.3 Configuring a Device to Communicate with an NM
Station by Running SNMPv2c

After SNMPv2c is configured, a managed device and an NM station can run SNMPv2c to
communicate with each other. To ensure normal communication, you need to configure both
sides. This section describes only the configurations on a managed device (the agent side). For
details about configurations on an NM station, see the pertaining NM station operation guide.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management

1 SNMP Configuration

Issue 01 (2011-10-26)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

15

«
...
24
25
26
27
28
...
»

Содержание S5700 Series
































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S5700 Series

BB-HGW700A - Network Camera Router

Бренд: Panasonic Страницы: 10

BiPAC 4500NZ(L)

Бренд: Billion Страницы: 146

Speed Touch 591s

Бренд: Alcatel Страницы: 184

Бренд: XtendLan Страницы: 52

Bolide BN-NVR/NX

Бренд: GSA Страницы: 101

Redbooks Emulex VFA5

Бренд: IBM Страницы: 15

Бренд: R.V.R. Elettronica Страницы: 171

Бренд: Allied Telesis Страницы: 136

Бренд: Planet Страницы: 32

ProLiant DL100 G2 DPSS

Бренд: HP Страницы: 155

NetStorage 6000

Бренд: HP Страницы: 192

ProLiant DL100 G2 DPSS

Бренд: HP Страницы: 44

Бренд: 3Com Страницы: 66

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды