Huawei S5700 Series Скачать руководство пользователя страница 322

Страница: 322 / 415

Step 5

(Optional) Run:

local-pw-type

{

local-pw-type

ip-interworking

}

The type of the local PW is configured. By default, the type is Ethernet.

Step 6

(Optional) Run:

label-type

{

control-word

label-alert

}

The type of the PW label is configured.

NOTE

When

label-type

is set to

control-word

, run the

remote-pw-id

command to configure

the ID of the remote end of the PW.

When

label-type

is set to

label-alert

, run the

destination-address

ipv4

ip-address

{

lsp-masklen

mask-length

lsp-loopback

loopback-address

}* command to configure the destination IP address to

the tested.

Step 7

Run:

local-pw-id

local-pw-id

The ID of the local end of the PW is configured.

Step 8

(Optional) Run the following commands to configure other parameters for the PWE3 Ping test.

To configure the response mode of the Echo packet, run the

lsp-replymode

{

no-reply

udp

udp-via-vpls

udp-router-alert

level-control-channel

} command.

To configure the LSP EXP value, run the

lsp-exp

exp

command.

Step 9

Run:

start

The NQA test is started.

Select the start mode as required because the

start

command has several forms.

To perform the NQA test immediately, run the

start

now

[

end

{

[

yyyy

]

delay

{

seconds

second

} |

lifetime

{

seconds

second

} ]

command.
The test instance is started immediately.

To perform the NQA test at the specified time, run the

start

[

yyyy

]

[

end

{

[

yyyy

]

delay

{

seconds

second

} |

lifetime

{

seconds

second

} ] command.

The test instance is started at a specified time.

To perform the NQA test after a certain delay period, run the

start

delay

{

seconds

second

} [

end

{

[

yyyy

]

delay

{

seconds

second

} |

lifetime

{

seconds

second

} ] command.

The test instance is started after a certain delay.

----End

6.20.3 Checking the Configuration

After performing the PWE3 ping test for a multi-hop PW, you can view the test result.

Prerequisite

The configurations of the PWE3 Ping Test function are complete.

Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management

6 NQA Configuration

Issue 01 (2011-10-26)

Huawei Proprietary and Confidential

311

Содержание S5700 Series
































































































































































































































































































































































































































Результаты поиска

Содержание S5700 Series

Отзывы:

Похожие инструкции для S5700 Series

Бренды по названию

Популярные бренды

Huawei S5700 Series, Конфигурационное руководство - Управление сетью

Результаты поиска

Содержание S5700 Series

Отзывы:

Похожие инструкции для S5700 Series

Бренды по названию

Популярные бренды