Huawei S5700 Series Скачать руководство пользователя страница 412 | Manualshive

Страница: 412 / 415

Huawei S5700 Series Скачать руководство пользователя страница 412

Figure 7-1

Networking diagram of configuring RMON

Configuration Roadmap

To send a Trap message to the NMS, you need to use SNMP commands to enable the Trap
function and set a corresponding community name. For details, refer to the chapter SNMP
Configuration.

The configuration roadmap is as follows:

l

Enable the statistics function.

l

Configure the etherStatsTable.

l

Configure the historyControlTable.

l

Configure the eventTable.

l

Configure the alarmTable.

Data Preparation

To complete the configuration, you need the following data:

l

Interval for sampling data

l

Threshold for triggering alarms

l

Community name for communicating with the NMS

Configuration Procedure

1.

Configure reachable routes between the Switch and the NMSs. The configuration procedure
is not mentioned.

2.

Enable the statistics function.
# Enable the RMON statistics function on the interface.

<Switch>

system-view

[Switch]

interface gigabitethernet 0/0/1

[Switch-GigabitEthernet0/0/1]

rmon-statistics enable

# Configure the etherStatsTable.

[Switch-GigabitEthernet0/0/1]

rmon statistics 1 owner User01

# Verify the configuration. You can check the traffic on the subnet.

[Switch-GigabitEthernet0/0/1]

display rmon statistics GigabitEthernet0/0/1

Quidway S5700 Series Ethernet Switches
Configuration Guide - Network Management

7 RMON Configuration

Issue 01 (2011-10-26)

Huawei Proprietary and Confidential

Copyright © Huawei Technologies Co., Ltd.

401

«
...
410
411
412
413
414
...
»

Содержание S5700 Series
































































































































































































































































































































































































































Отзывы:

Нет отзывов