HSM SP 5080 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 57

HSM SP 5080 Скачать руководство пользователя страница 43

04/2013

2.990.999.120_en

43

SP 5080

4.6

Malfunctions of the baling press

As soon as a malfunction occurs in the baling press, the red malfunction symbol lights
up. The baling press and shredder switch off and the relevant error message appears in
the text display.

The “Baling press status” symbol

lights up red on the shredder.

The error number of the most recent error is stored in the error memory.
Diverse, displayed error messages can be cleared by simultaneously pressing the + / –
keys or by turning the machine on and off.

Service - Hotline: +49 75 54/2100-300

4.6.1 Error

numbers

Code

Description

Remedy

1000

One of the phases is missing / power input

Electrician! Check the fuses on site.

1010

A phase is wrong / counter-clockwise phase rotation

Electrician! Phase sequence on site / check phase rotation.

1100

Oil temperature too high

Let oil cool / check oil temperature sensor

1110

Defective oil temperature sensor

Electrician! Replace sensor

1200

Motor overload switch was triggered. Motor too hot

Check motor / reset motor overload switch

1210

Emergency stop on the press has been activated

Unlock the emergency stop button

1211

Emergency stop on the shredder has been activated

Unlock the emergency stop button

1221

Service door in the fi lling area of the press is open

Close the inspection fl ap

1231

Defective “Counter fl ap closed” switch

Electrician! Consult HSM customer service

1232

Counter fl ap is open

Close the counter fl ap

1241

Defective “Counter fl ap 90° open” switch

Electrician! Consult HSM customer service

1271

“Extend press ram” timing

Check the movement of the press ram

1272

“Retract press ram” timing

Check the movement of the press ram

1280

Counter plate not locked

Electrician! Consult HSM customer service

1281

Defective “Bale ready” inductive switch

Electrician! Consult HSM customer service

1285

Defective counter plate locked inductive switch

Electrician! Consult HSM customer service

1300

Defective hardware

Electrician! Consult HSM customer service

1310

Short-circuit master output stage

Electrician! Consult HSM customer service

1320

Short-circuit slave output stage

Electrician! Consult HSM customer service

«
...
41
42
43
44
45
...
»

Содержание SP 5080


























































Отзывы:

Нет отзывов