HP ProLiant ML110 G7 Скачать руководство пользователя

Страница: 58 / 113

Hardware options installation 58

11.

Do one of the following:

For improved power efficiency, install an HP CS power supply in the upper bay of the RPS cage.

NOTE:

To install a second redundant power supply in the redundant power supply cage, first

remove the cage EMI shield.

CAUTION:

The default and redundant power supplies in the server must have the same output

power capacity. Verify that all power supplies have the same part number and label color. The

system becomes unstable and might shut down when it detects mismatched power supplies.

NOTE:

To install a second redundant power supply in the redundant power supply cage, first

remove the cage EMI shield.

Содержание ProLiant ML110 G7


















































































































Результаты поиска

Содержание ProLiant ML110 G7

Отзывы:

Похожие инструкции для ProLiant ML110 G7

Бренды по названию

Популярные бренды

HP ProLiant ML110 G7, Руководство пользователя

Результаты поиска

Содержание ProLiant ML110 G7

Отзывы:

Похожие инструкции для ProLiant ML110 G7

Бренды по названию

Популярные бренды