background image

 

Troubleshooting  87 

 

 

POST problems flowchart 

Symptoms: 

 

Server does not complete POST 

  

 

NOTE:

  The server has completed POST when the system attempts to access the boot device. 

  

 

Server completes POST with errors 

Possible problems: 

 

Improperly seated or faulty internal component 

 

Faulty KVM device 

 

Faulty video device 

    

Item 

See 

"Video problems" in the 

HP ProLiant Servers Troubleshooting Guide

 

located on the Documentation CD or see "Troubleshooting resources (on 

page 

76

)" 

KVM or iLO documentation 

"POST error messages and beep codes (on page 

92

)" 

"Symptom information (on page 

78

)" 

"Port 85 and iLO messages" in the 

HP ProLiant Servers Troubleshooting 

Guide

 located on the Documentation CD or see "Troubleshooting resources 

(on page 

76

)" 

"Server health LEDs (on page 

81

)" and "Component identification (on 

page 

7

)" 

"Loose connections (on page 

80

)" 

"General memory problems are occurring" in the 

HP ProLiant Servers 

Troubleshooting Guide

 located on the Documentation CD or see 

"Troubleshooting resources (on page 

76

)" 

Server maintenance and service guide, located on the Documentation CD 
or the HP website (

http://www.hp.com/products/servers/platforms

). 

10 

"Breaking the server down to the minimum hardware configuration (on 

page 

79

)" or in the 

HP ProLiant Servers Troubleshooting Guide

 located on 

the Documentation CD or see "Troubleshooting resources (on page 

76

)" 

11 

 

"Hardware problems" in the 

HP ProLiant Servers Troubleshooting 

Guide

 located on the Documentation CD or see "Troubleshooting 

resources (on page 

76

)" 

 

Server maintenance and service guide, located on the Documentation 

CD or the HP website 
(

http://www.hp.com/products/servers/platforms

12 

"HP contact information (on page 

99

)" 

Содержание ProLiant ML110 G7


















































































































Отзывы: