HP ProLiant BL p-Class GbE2 Скачать руководство пользователя страница 123

Страница: 123 / 126

Index

Gigabit Ethernet, configuration 6-12

cost

global commands 2-3

STP information 4-13

Greenwich Mean Time (GMT) 6-10

STP port option 6-22

grounding vii

CPU statistics 5-14

grounding plug vii
gtcfg (TFTP load command) 6-28

date setup 3-4

daylight savings time 6-10

health checks

debugging 9-1

default gateway interval, retries 6-16

default gateway, interval for health checks 6-16

retry, number of failed health checks 6-16

default password

hello, STP information 4-13

administrator 3-11

help resources viii

operator 3-14

history command 2-4

user 3-13

HP authorized reseller viii

diff command 2-3, 6-2

HTTP, system option 6-6

diff flash command   2-3, 6-2
DISABLED (port state)   4-13
disconnect idle timeout   1-7

Domain Name System (DNS) Configuration

Menu 6-17

idle timeout, overview 1-7
IEEE standards, 802.1D Spanning Tree

Protocol 4-12, 6 -19

Domain Name System (DNS) statistics 5-26
download software 8-2

image

dump

download 8-2

configuration 6-27

software, selection 8-3

information 4-17

information dump 4-17

state information 9-7

Information Menu 4-1

statistics 5-26

interface statistics 5-9, 5-15

duplex mode, link status 4-2, 4 -11

Internet Control Messaging Protocol (ICMP)

statistics 5-18

IP address

ethernet statistics 5-5

ARP information 4-5
BOOTP 1-3
default gateway configuration 6-16

IP interface 3-8

factory configuration block 8-5

mmask 6-5

factory default configuration 3-1, 3-2

mnet 6-5

first-time configuration 3-1

IP Configuration Menu 6-14

flow control

IP configuration via setup 3-8

configuration 6-13

IP interface

display setting 4-2

address configuration 6-15

link status 4-11

broadcast address (broad) 6-15

Forwarding Database (FDB)

information 4-16

maintenance 9-3

via setup 3-8

statistics 5-25

VLAN configuration 6-15

Forwarding Database Information Menu 4-7

IP Interface Configuration Menu 6-15

Forwarding Database Manipulation Menu 9-3

IP routing 3-8

forwarding state (FWD) 4-8, 4-13, 4-16

IP statistics 5-17

fwd (STP bridge option) 6-21
FwdDel (forward delay), bridge port 4-13

LEARNING (port state) 4-13

lines command 2-3

gig (Port Menu option) 6-12

link speed, configuration 6-13

Gigabit Ethernet Physical Link 6-12

link statistics 5-11

Index-2

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

COMPAQ CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 1:12 PM

Содержание ProLiant BL p-Class GbE2































































































































Результаты поиска

Содержание ProLiant BL p-Class GbE2

Отзывы:

Похожие инструкции для ProLiant BL p-Class GbE2

Бренды по названию

Популярные бренды

HP ProLiant BL p-Class GbE2, Справочник по командам

Результаты поиска

Содержание ProLiant BL p-Class GbE2

Отзывы:

Похожие инструкции для ProLiant BL p-Class GbE2

Бренды по названию

Популярные бренды