HP ProLiant BL p-Class GbE2 Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 126

background image

The Configuration Menu

NTP Server Configuration

Command:

/cfg/sys/ntp

[NTP Server Menu]
server - Set NTP server address
intrval - Set NTP server resync interval
tzone - Set NTP timezone offset from GMT
dlight - Enable or disable NTP daylight saving time
on - Turn NTP service ON
off - Turn NTP service OFF
cur - Display current NTP configuration

This menu enables you to synchronize the GbE2 Interconnect Switch clock to a Network
Time Protocol (NTP) server. By default, this option is disabled.

The following table describes the

NTP Server Configuration Menu

options.

Table 6-6: NTP Server Configuration Menu Options

Command Description

server

<NTP Server IP address>

Prompts for the IP addresses of the NTP server
to which you want to synchronize the GbE2
Interconnect Switch clock.

intrval

<resync interval in

minutes>

Specifies the interval, that is, how often, in
minutes (1-2880), to resynchronize the GbE2
Interconnect Switch clock with the NTP server.

tzone

<timezone offset, in HH:MM

format>

Prompts for the NTP time zone offset from
Greenwich Mean Time (GMT), in hours and
minutes.

dlight disable|enable

Disables or enables daylight saving time in the
system clock. When enabled, the GbE2
Interconnect Switch will add an extra hour to the
system clock so that it is consistent with the
local clock. By default, this option is disabled.

on

Enables the NTP synchronization service.

off

Disables the NTP synchronization service. This
is the default.

cur

Displays the current NTP service settings.

6-10

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:57 PM

«
...
86
87
88
89
90
...
»

Содержание ProLiant BL p-Class GbE2































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProLiant BL p-Class GbE2

Бренд: Barksdale Страницы: 6

DGS-1224TP - Web Smart Switch

Бренд: D-Link Страницы: 52

Бренд: D-Link Страницы: 8

DES-3225G Series

Бренд: D-Link Страницы: 3

DES-1228 - Web Smart Switch

Бренд: D-Link Страницы: 69

Бренд: D-Link Страницы: 109

Бренд: Barco Страницы: 2

Бренд: Alyseum Страницы: 7

Бренд: CZHOON Страницы: 4

Infinity IES-1881

Бренд: LevelOne Страницы: 2

Xbox One Media Hub

Бренд: Collective Minds Страницы: 19

Elinx EIR418-2SFP-T

Бренд: B&B Electronics Страницы: 25

Бренд: CIS Страницы: 3

Бренд: Nobile Страницы: 2

Бренд: Woxcon Страницы: 42

Бренд: M-system Страницы: 4

Бренд: Atlona Страницы: 22

Бренд: National Instruments Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды