HP ProLiant BL p-Class GbE2 Скачать руководство пользователя страница 37

Страница: 37 / 126

The Information Menu

Table 4-1: Information Menu Options

continued

Command Usage

sys

Displays system information, including:

•

System date and time

•

GbE2 Interconnect Switch model name and number

•

GbE2 Interconnect Switch name and location

•

GbE2 Interconnect Switch rack ID, chassis location, and slot
occupied

•

Time of last boot

•

MAC address of the GbE2 Interconnect Switch management
processor

•

IP address of IP interface #1

•

Hardware version and part number

•

Software image file and version number

•

Current configuration block

•

Log-in banner, if one is configured

log

Displays the 30 most recent

syslog

messages.

link

Displays configuration information about each port, including:

•

Port number

•

Port speed (10 Mb/s, 100 Mb/s, 1000 Mb/s, or any)

•

Duplex mode (half, full, or any)

•

Flow control for transmit and receive (no, yes, or any)

•

Link status (up or down)

4-2

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:51 PM

Содержание ProLiant BL p-Class GbE2































































































































Результаты поиска

Содержание ProLiant BL p-Class GbE2

Отзывы:

Похожие инструкции для ProLiant BL p-Class GbE2

Бренды по названию

Популярные бренды

HP ProLiant BL p-Class GbE2, Справочник по командам

Результаты поиска

Содержание ProLiant BL p-Class GbE2

Отзывы:

Похожие инструкции для ProLiant BL p-Class GbE2

Бренды по названию

Популярные бренды