HP ProLiant BL p-Class GbE2 Скачать руководство пользователя страница 108

Страница: 108 / 126

The Operations Menu

7-2

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 1:09 PM

Operations-Level Port Options

Command:

/oper/port

<port number>

[Operations Port 1 Menu]

ena - Enable port
dis - Disable port
cur - Current port state

Operations-level port options are used for temporarily disabling or enabling a port.

Table 7-2: Operations-Level Port Menu Options

Command Description

ena

Temporarily enables the port. The port will be returned to its
configured operation mode when the GbE2 Interconnect Switch
is reset.

dis

Temporarily disables the port. The port will be returned to its
configured operation mode when the GbE2 Interconnect Switch
is reset.

cur

Displays the current settings for the port.

Содержание ProLiant BL p-Class GbE2































































































































Результаты поиска

Содержание ProLiant BL p-Class GbE2

Отзывы:

Похожие инструкции для ProLiant BL p-Class GbE2

Бренды по названию

Популярные бренды

HP ProLiant BL p-Class GbE2, Справочник по командам

Результаты поиска

Содержание ProLiant BL p-Class GbE2

Отзывы:

Похожие инструкции для ProLiant BL p-Class GbE2

Бренды по названию

Популярные бренды