HP ProLiant BL p-Class GbE2 Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 126

background image

The Configuration Menu

Port Configuration

Command:

/cfg/port

<port number>

[Port 1 Menu]
gig - Gig Phy Menu
pvid - Set default port VLAN id

name - Set port name
tag - Enable/disable VLAN tagging for port
iponly - Enable/disable allowing only IP related frames
ena - Enable port
dis - Disable port
cur - Display current port configuration

This menu enables you to configure settings for individual GbE2 Interconnect Switch ports.
This command is enabled by default.

The following table describes the

Port Configuration Menu

options.

Table 6-8: Port Configuration Menu Options

Command Description

gig

This option displays the

Gigabit Ethernet Physical

Link Menu.

pvid

<VLAN number, 1-4094>

Sets the default VLAN number which will be used to
forward frames which are not VLAN tagged. The
default number is 1.

name

<64 character string>

|none

Sets a name for the port. The assigned port name
displays next to the port number on some
information and statistics screens. The default is set
to none.

tag disable|enable

Disables or enables VLAN tagging for this port. It is
disabled by default.

iponly disable|enable

Disables or enables allowing only IP-related frames.
It is disabled by default.

ena

Enables the port.

dis

Disables the port. To temporarily disable a port
without changing its configuration attributes, refer to
the “Temporarily Disabling a Port” section, later in
this chapter.

cur

Displays current port parameters.

6-12

HP ProLiant BL p-Class GbE2 Interconnect Switch Command Reference Guide

HP CONFIDENTIAL

Codename: Strawberry Part Number: 331404-001 Last Saved On: 7/17/03 12:57 PM

«
...
88
89
90
91
92
...
»

Содержание ProLiant BL p-Class GbE2































































































































Отзывы:

Нет отзывов

Похожие инструкции для ProLiant BL p-Class GbE2

RackSwitch G8264

Бренд: IBM Страницы: 20

Flex System FC3171

Бренд: IBM Страницы: 64

Бренд: H3C Страницы: 32

Бренд: H3C Страницы: 22

Бренд: H3C Страницы: 488

Бренд: H3C Страницы: 3

Бренд: H3C Страницы: 8

Бренд: H3C Страницы: 25

Бренд: H3C Страницы: 31

Бренд: H3C Страницы: 23

Бренд: H3C Страницы: 24

Бренд: H3C Страницы: 126

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 32

Бренд: H3C Страницы: 13

Бренд: H3C Страницы: 16

Бренд: H3C Страницы: 39

Бренд: H3C Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды