HP 85106D Скачать руководство пользователя страница 146

Страница: 146 / 244

HP 85106D mm-Wave System

5-33

HP 85104A Test Set Module

Disassembly Procedure

Procedure

NOTE

The disassembly procedure must be followed in sequence. It is not the
reverse of the assembly procedure.

1. Turn the test set module over so the bottom side is facing up. Remove

the stand by loosening the two captive screws until the module and stand
are disengaged.

2. Remove all extensions from the HP 85104A.

3. Remove the two torx-head screws from the bottom housing and pull the

bottom housing off.

4. Slide the front panel up and out. Cut and remove the cable ties.

5. Disconnect the RF and LO cables from the 90° coaxial bends that are

connected to the main top mount (near the power divider).

6. Remove the cable clamp.

7. Disconnect the IF cabling (red/white and blue/white) from the mixers.

8. Disconnect the module interface connector from the A5 board, (part of

A13 source block).

9. Disconnect the ALC cable yellow/white) from the A5 board.

NOTE

In some modules the ALC cable may not be accessible at this time. Remove
this cable when it becomes accessible.

10. For V-or W-band modules, disconnect the detector cable from the A5

board (part of A13 source block). Leave the A5 cable connected to A14
detector.

NOTE

The coupler/detector (A14) and the source block (A13) must be returned to
the factory together (attached with two screws) if either component is faulty.

11. Remove the rear panel/cable assembly.

12. Remove the hex-head screws from the bottom mount and remove the

mount.

13. Remove the semi-rigid coaxial cables from the LO power divider to the

mixers.

14. Remove the four mixer bracket screws and remove the mixer bracket

from both sides of the source block.

Содержание 85106D





















































































































































































































































Результаты поиска

Содержание 85106D

Отзывы:

Похожие инструкции для 85106D

Бренды по названию

Популярные бренды

HP 85106D, Руководство пользователя

Результаты поиска

Содержание 85106D

Отзывы:

Похожие инструкции для 85106D

Бренды по названию

Популярные бренды