HP 85106D Скачать руководство пользователя страница 51

Страница: 51 / 244

2-6

HP 85106D mm-Wave System

Operation

System Set Up

Procedure

The following procedure describes loading the network analyzer memory
from the system disk.

1. Load the desired Machine Dump file from the system. Insert the disk

into the internal drive of the HP 8510C external disk drive. Press the
following keys:

[

DISK

]

{

STORAGE IS INTERNAL

}

{

LOAD

}

{

MORE

}

{

MACHINE DUMP

}

Use the RPG knob to select the file for the desired frequency band
(see Table ).

Press: {

LOAD FILE

} to start the process.

Table 2-1

Machine Dump Files Stored On The mm-Wave System Disk

NOTE

If your system contains an extra test set (HP 85106D Option 001), verify that
only the desired test set is active (active light ON). If unselected test sets are
active, deactivate the test set temporarily by pressing [

LOCAL

] {

TEST SET

Then return to the desired address.

2. When the Machine Dump file is loaded the system begins sweeping the

full frequency range of the current band. Press [

CAL

] and read the

{

CAL 1

} label to see whether the calibration kit for the desired band is

loaded.

3. The system is ready for operation. You may change the instrument state

settings for specific applications.

Frequency
Range

45 MHz - 50 GHz

33 GHz -50 GHz

40 GHz -60 GHz

50 GHz -75 GHz

75 GHz -110 GHz

Frequency

Band

Coaxial

((option001)

Waveguide

Q-band

WR-22

U-band

WR-19

V-band
WR-15

W-band

WR-10

Machine

Dump Files

MD_COAX

MD_SYNWR22

MD_SYNWR19

MD_SYNWR15

MD_SYNWR10

Содержание 85106D





















































































































































































































































Результаты поиска

Содержание 85106D

Отзывы:

Бренды по названию

Популярные бренды

HP 85106D, Руководство пользователя

Результаты поиска

Содержание 85106D

Отзывы:

Бренды по названию

Популярные бренды