HP 85106D Скачать руководство пользователя страница 198 | Manualshive

Страница: 198 / 244

background image

HP 85106D mm-Wave System

6-33

HP 85105A mm-Wave Controller

LO ALC Adjustment

1. Run the system software and select {

HIGHBAND

} to make the mm-wave

controller active.

2. Check the user parameter (al or a2) for the LO port in question. The

trace should be -15

±

2 dBm across the band as displayed on the

HP 8510 CRT. If this is the case the LO ALC is adjusted properly.
If the message

NO IF FOUND

is displayed and/or a trace is not observed

at the level mentioned, the LO ALC adjustment needs to be made,
continue with step 3.

NOTE

Step 3 should only be performed when an amplifier, coupler, or detector has
been replaced.

3. Connect the oscilloscope and negative detector as shown in Figure 6-16

on page 6-32. Turn the gain adjustment fully clockwise. Oscillations
should be visible on the oscilloscope. Turn the gain adjustment counter
clockwise until the oscillations just disappear. Recheck the user
parameters in step 2 and then continue with step 4.

4. Choose a power meter that covers the 4 to 6 GHz frequency range

(HP 436A meter and HP 8485A sensor). Calibrate the power meter
and attach a 3.5 mm 10 dB fixed attenuator (HP 8493C) and an adapter
(female to female) to the sensor. Connect the sensor/attenuator to the LO
output of the port in question. Turn the LO level adjustment so that
+12 dBm is displayed on the power meter. The LO output is now set at
+22 dBm. Select {

SINGLE POINT MODE

} from the [

STIMULUS

] menu, then

using the RPG knob, slowly scan over the frequency band.

5. Adjust the LEVEL pot over the full adjustment range to make sure there

are no oscillations at any power level. Then turn the GAIN pot three
additional turns.

«
...
196
197
198
199
200
...
»

Содержание 85106D





















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 85106D

Mentor Visual iQ

Бренд: GE Страницы: 2

Бренд: jenway Страницы: 20

Бренд: QuantAsylum Страницы: 70

Бренд: Saluki Страницы: 312

Бренд: Yamaha Страницы: 6

Бренд: Daewoo Страницы: 17

Бренд: Bamo Страницы: 17

Бренд: Keller Страницы: 4

PLUS 3631 Series

Бренд: insize Страницы: 1

Бренд: Datakom Страницы: 28

Бренд: Rhosonics Страницы: 65

Бренд: Kane Страницы: 35

Бренд: Veris Страницы: 3

Бренд: Hanna Instruments Страницы: 2

Бренд: Zero 88 Страницы: 32

microCLIMA ULTRA

Бренд: MADDALENA Страницы: 17

Бренд: Velleman Страницы: 38

Бренд: Rebel Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды