HP 85106D Скачать руководство пользователя страница 209 | Manualshive

Страница: 209 / 244

background image

HP 85106D mm-Wave System

6-45

HP 85105A mm-Wave Controller

Replaceable Parts

Replaceable Parts

This section contains information for ordering replaceable parts. The
replaceable parts include major assemblies and chassis hardware.

R-E
(Rebuilt-Exchange)
Assemblies Cost Less

Some assemblies are available through the rebuilt-exchange program.
These factory rebuilt (repaired and tested) assemblies meet all factory
specifications required of a new assembly. They are offered on an exchange
(trade-in) basis only. The defective assembly must be returned for credit.
Figure 6-27 on page 6-47 illustrates the procedure. The rest of the figures
provide parts information. If you have any questions, contact your HP
customer engineer.

Replaceable Parts List

The following figures assist in locating and identifying all replaceable parts,
including corresponding lists that provide the following information.

•

Hewlett-Packard part number.

•

Part quantity as shown in the figure. There may be more of the same part
in the instrument.

•

Part description, using abbreviations.

Ordering Information

To order a part listed in the replaceable parts lists:

•

Quote the Hewlett-Packard part number.

•

Indicate the quantity required.

•

Address the order to the nearest Hewlett-Packard office.

To order a part that is not listed:

•

Include the instrument model number.

•

Complete serial number.

•

Description and function of the part.

•

Number of parts required.

•

Address the order to the nearest Hewlett-Packard office.

«
...
207
208
209
210
211
...
»

Содержание 85106D





















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 85106D

Бренд: Valeport Страницы: 25

Бренд: WAGER Страницы: 36

Бренд: UEi Страницы: 8

Бренд: G-Tek Страницы: 83

Level Pro UltraPro 500 Series

Бренд: Icon Process Controls Страницы: 19

Бренд: Divertug Страницы: 47

Бренд: AccuMac Страницы: 10

International 2S Pro

Бренд: Brantz Страницы: 2

Бренд: Salutron Страницы: 2

Stream Line Pro

Бренд: Halo Photonics Страницы: 45

Stubby LED-1500

Бренд: Dive Perfect Страницы: 4

Бренд: Omega Страницы: 22

Бренд: Hanna Instruments Страницы: 2

Бренд: Vogel Страницы: 4

K-PATENTS PR-23 AX Series

Бренд: Vaisala Страницы: 246

Бренд: IFM Страницы: 13

ProScale 950 Series

Бренд: Accurate Technology Страницы: 16

Бренд: Omega Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды