HP 85106D Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 244

background image

iv

HP 85106D mm-Wave System

Certification

Hewlett-Packard Company certifies that this product met its published
specifications at the time of shipment from the factory. Hewlett-Packard
further certifies that its calibration measurements are traceable to the
United States National Institute of Standards and Technology (NIST,
formerly NBS), to the extent allowed by the Institute’s calibration facility,
and to the calibration facilities of other International Standards
Organization members.

Warranty

This Hewlett-Packard system product is warranted against defects in
materials and workmanship for a period corresponding to the individual
warranty periods of its component products. Instruments are warranted for a
period of one year. During the warranty period, Hewlett-Packard Company
will, at its option, either repair or replace products that prove to be defective.

Warranty service for products installed by HP and certain other products
designated by HP will be performed at Buyer’s facility at no charge within
HP service travel areas. Outside HP service travel areas, warranty service
will be performed at Buyer’s facility only upon HP’s prior agreement and
Buyer shall pay HP’s round trip travel expenses. In all other areas, products
must be returned to a service facility designated by HP.

For products returned to HP for warranty service, Buyer shall prepay
shipping charges to HP and HP shall pay shipping charges to return the
product to Buyer. However, Buyer shall pay all shipping charges, duties, and
taxes for products returned to HP from another country.

HP warrants that its software and firmware designated by HP for use with an
instrument will execute its programming instructions when properly
installed on that instrument. HP does not warrant that the operation of the
instrument, or software, or firmware will be uninterrupted or error free.

LIMITATION OF WARRANTY. The foregoing warranty shall not apply
to defects resulting from improper or inadequate maintenance by Buyer,
Buyer-supplied software or interfacing, unauthorized modification or
misuse, operation outside of the environmental specifications for the
product, or improper site preparation or maintenance.

NO OTHER WARRANTY IS EXPRESSED OR IMPLIED. HP
SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OR
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

EXCLUSIVE REMEDIES. THE REMEDIES PROVIDED HEREIN ARE
BUYER’S SOLE AND EXCLUSIVE REMEDIES. HP SHALL NOT BE
LIABLE FOR ANY DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, WHETHER BASED ON CONTRACT,
TORT, OR ANY OTHER LEGAL THEORY.

«
...
3
4
5
6
7
...
»

Содержание 85106D





















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 85106D

Бренд: Teac Страницы: 148

Бренд: IFM Страницы: 25

Бренд: Campbell Страницы: 16

Бренд: Ulvac Страницы: 18

Бренд: Yamaha Страницы: 72

Бренд: Yamaha Страницы: 5

Бренд: Yamaha Страницы: 16

Бренд: Yamaha Страницы: 8

Бренд: Yamaha Страницы: 7

Бренд: Yamaha Страницы: 60

GranTouch Digital Grand Piano

Бренд: Yamaha Страницы: 19

Бренд: Yamaha Страницы: 44

Бренд: Yamaha Страницы: 29

Бренд: Yamaha Страницы: 47

Бренд: M-Sure Страницы: 2

Бренд: POSEIDON Страницы: 13

Бренд: AKCP Страницы: 16

Бренд: Swann Страницы: 106

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды