NOTE:
Names, such as host names, must begin with a letter and can contain
only letters, numbers, periods (for domain names only), or hyphens. The underline
character (_) is not allowed.
ip-config
Specify the configuration method:
manual
: The print server will wait for IP parameters using manual tools (such as Telnet,
embedded Web server, control panel, installation/management software). Status will be
User Specified
.
bootp
: The print server will send BOOTP requests on the network for dynamic IP
configuration.
dhcp
: The print server will send DHCP requests on the network for dynamic IP
configuration.
auto_ip
: The print server will be automatically configured with a unique link-local address
169.254.x.x.
ipsec-config
firewall-config
The
ipsec-config
command is supported on print servers and printers that support both
IPsec and Firewall configurations. The
firewall-config
command is supported on full-
featured print servers that do not support IPsec, but allow Firewall configuration.
Use these commands to disable IPsec or Firewall operation on the print server after IPsec/
Firewall policies have been configured and enabled. IPsec/Firewall operation cannot be
enabled by this command; if IPsec/Firewall policies are enabled, the status will be “read
only”.
0
: Disable IPsec/Firewall operation, if it is enabled.
1
: (Read Only) Indicates IPsec/Firewall policies are configured and enabled. Use the
embedded Web server to configure and enable IPsec/Firewall policies.
ip
IP address for the print server, in dotted notation. For example:
ip-config manual ip 192.168.45.39
where
manual
specifies manual configuration and
ip
manually sets the IP address
192.168.45.39 on the print server.
Specifying 0.0.0.0 clears the IP address.
If you exit and save a new IP address, it must be specified on the next Telnet connection.
subnet-mask
A value (in dotted notation) that identifies the network and host portions of an IPv4 address
in received messages. For example,
subnet-mask 255.255.255.0
stores the subnet mask value 255.255.255.0 on the print server. The value 0.0.0.0 disables
the subnet mask.
default-gw
The IP address of a default gateway, in dotted notation. For example,
default-gw 192.168.40.1
assigns 192.168.40.1 as the IP address of the default gateway for the print server.
NOTE:
If the HP Jetdirect print server is configured by DHCP and you manually
change the subnet mask or the default gateway address, you should manually
change the print server's IP address. This will release the DHCP-assigned
address back to the DHCP IP address pool.
Table 3-3
Telnet Commands and Parameters (continued)
ENWW
IPv4 Configuration
45
Содержание 635n - JetDirect IPv6/IPsec Print Server
