Message
Description
Specified
: An 802.1X authentication protocol other than EAP-TLS/EAP-PEAP has been
configured.
Not Specified
: 802.1X authentication has not been configured.
IPsec
or
Firewall
If the print server and printer/MFP device supports IPsec, then
IPsec
will appear. If IPsec
is not supported, then
Firewall
will appear.
Provides the print server's current IPsec/Firewall status.
Enabled
: IPsec/Firewall is enabled and operating as configured by the user.
Disabled
: IPsec/Firewall is turned off.
Policy Failed
: The print server failed to implement the IPsec policy that was configured.
You may need to reset security (through the control panel or embedded Web server),
or perform a cold-reset of the print server.
Admin Password
Specifies whether an IP Administrator password has been configured on the print
server. This password is shared by Telnet, the embedded Web server, and HP Web
Jetadmin to control access to print server configuration parameters. Up to 16 case-
sensitive, alphanumeric characters can be used.
Not Specified
: An Administrator password has not been set.
Set
: An Administrator password has been set.
(The password may be cleared from the print server through a cold reset.)
Cert Expires
Specifies the expiration date of the digital certificate for SSL/TLS encrypted security.
The date is in UTC format (for example, “2002-10-02 12:45 UTC”).
Not
Applicable
: Displayed if a digital certificate has not been installed.
SNMP Versions
Specifies the SNMP versions enabled on the print server.
Disabled
: All SNMP versions are disabled on the print server. No SNMP access is
allowed.
1;2
: SNMP v.1 and SNMP v.2c are supported, and SNMP v.3 is disabled, or not
supported.
1;2;3-na/np
: SNMP v.1, v.2c, and v.3 are enabled. v.3 is enabled with the minimum
security of no authentication (“na”) and no privacy (“np”).
1;2;3-a/np
: SNMP v.1, v.2c, and v.3 are enabled. v.3 is enabled with the minimum
security of authentication enabled (“a”) but no privacy (“np”).
1;2;3-a/p
: SNMP v.1, v.2c, and v.3 are enabled. v.3 is enabled with the minimum security
of authentication (“a”) with privacy (“p”) enabled.
3-na/np
: SNMP v.1 and v.2c are disabled. SNMP v.3 is enabled with the minimum
security of no authentication (“na”) and no privacy (“np”).
3-a/np
: SNMP v.1 and v.2c are disabled. SNMP v.3 is enabled with the minimum
security of authentication enabled (“a”) but no privacy (“np”).
3-a/p
: SNMP v.1 and v.2c are disabled. SNMP v.3 is enabled with the minimum security
of authentication (“a”) with privacy (“p”) enabled.
SNMP Set Cmty Name
Specifies whether an SNMP set community name has been configured on the HP
Jetdirect print server. An SNMP set community name is a password for write access to
SNMP control functions (SNMP SetRequests) on the HP Jetdirect print server.
Not Specified
: An SNMP set community name has not been set.
Table 8-4
Security Settings (continued)
132 Chapter 8 HP Jetdirect Configuration Pages
ENWW
Содержание 635n - JetDirect IPv6/IPsec Print Server
