CAUTION:
Ensure that command parameters are properly entered and that the
upgrade file is a higher version than the currently installed version. The print server
will attempt to upgrade when the upgrade file contains a higher version than the
installed version.
The command format is:
upgrade: <TFTP server IP> <Version> <Product Number> <Filename>
where,
<TFTP Server IP>
is the IP address of the TFTP server,
<Version>
specifies the
firmware version of the upgrade file,
<Product Number>
specifies and must match the
product number of the print server,
<Filename>
is the path and filename of the firmware
upgrade file.
laa
Specifies a locally administered address (LAA) that replaces the factory-assigned LAN
Hardware (MAC) address. If LAA is used, a user-specified string of exactly 12 hexadecimal
digits must be entered.
For Ethernet print servers, the LAA address must start with hexadecimal X2, X6, XA, or
XE, where X is any hexadecimal digit 0 through F.
The default address is the factory-assigned address.
xml-services-conf
Enable or disable access by HP Web service applications to XML-based data on the HP
Jetdirect print server.
1
(default): Enable
0
: Disable
ws-discovery-conf
Enable or disable the Microsoft Web Services Dynamic Discovery (WS Discovery)
protocols on the print server.
1
(default): Enable
0
: Disable
1000t-ms-conf
Use this command to configure the print server as a master or slave device on a 1000T
network.
AUTO
or
0
(default): A master/slave configuration is automatically sensed and assigned.
MASTER
or
1
: The device is configured as a 1000T master device.
SLAVE
or
2
: The device is configured as a 1000T slave device.
1000t-pause-conf
This command is used for flow control of inbound and outbound data.
OFF
or
0
(default): Flow control is disabled.
AUTO
or
1
: Flow control is configured through auto-negotiation with the network switch.
RCV
or
2
: Flow control is enabled only for data received from the network.
TRANS
or
3
: Flow control is enabled only for data transmitted to the network.
TXRX
or
4
: Flow control is enabled for both received and transmit data.
link-type
(For wired 10/100/1000T Ethernet) Sets the print server's link speed (10, 100, 1000 Mbps)
and communication mode (Full- or Half-Duplex). The available link-speed selections
depend on the print server model. The selections that may be displayed are listed below.
Table 3-3
Telnet Commands and Parameters (continued)
ENWW
IPv4 Configuration
55
Содержание 635n - JetDirect IPv6/IPsec Print Server
