Menu Item
Description
SECURITY
Specify whether the current security settings on the print server will be saved or reset to factory
defaults.
KEEP
(default): The current security settings are maintained.
RESET
: Security settings are reset to factory defaults.
IPSEC
or
FIREWALL
NOTE:
(Full-featured print servers only) If the print server supports IPsec, then
IPSEC
will appear on the menu for both IPsec or Firewall status. If the print server does
not support IPsec, then Firewall will appear.
Specify the state of IPsec/Firewall on the print server.
KEEP
(default): IPsec/Firewall operation will be maintained as currently configured on the print
server.
DISABLE
: IPsec/Firewall will be disabled on the print server.
Print a configuration page for the selected item.
PROTOCOLS
: Use this item to print a page containing the configuration of the following protocols:
IPX/SPX, Novell NetWare, AppleTalk, DLC/LLC.
SECURITY
: Use this item to print a page that contains the current security settings on the HP
Jetdirect print server.
CFG LINK
Selects whether you want to manually configure the HP Jetdirect print server's network link.
NO
(default): Bypass the link configuration menu items.
YES
: Access the link configuration menu items.
The link speed and communication mode of the print server must match the network. The
available settings depend on the print server model. One of the following link configuration
settings can be selected:
CAUTION:
If you change the link setting, network communications with the print server
and network device may be lost.
AUTO
(default): The print server uses auto-negotiation to configure itself with the highest link
speed and communication mode allowed. If auto-negotiation fails, either 100TX HALF or 10TX
HALF is set depending on the detected link speed of the hub/switch port. (A 1000T half-duplex
selection is not supported.)
10T HALF
: 10 Mbps, half-duplex operation.
10T FULL
: 10 Mbps, Full-duplex operation.
100TX HALF
: 100 Mbps, half-duplex operation.
100TX FULL
: 100 Mbps, full-duplex operation.
100TX AUTO
: Limits auto-negotiation to a maximum link speed of 100 Mbps.
1000 FULL
: 1000 Mbps, full-duplex operation.
Table C-2
HP Jetdirect EIO Menu on Classic Control Panel (continued)
180 Appendix C HP Jetdirect Control Panel Menus (V.36.xx)
ENWW
Содержание 635n - JetDirect IPv6/IPsec Print Server
