Menu Item
Description
If you specify
BOOTP=NO*
,
DHCP=NO*
and
AUTO IP=NO*
, you can manually set the
following TCP/IPv4 parameters from the control panel:
●
Each byte of the IPv4 address (IP)
●
Subnet Mask (SM)
●
Syslog Server (LG)
●
Default Gateway (GW)
●
Idle Timeout period (default is 270 seconds, 0 disables the timeout)
●
CFG DNS 1=YES*
will allow you to specify the IPv4 address of a primary DNS server, one
byte at a time.
●
CFG DNS 2=YES*
will allow you to specify the IPv4 address of a secondary DNS server,
one byte at a time.
●
IPV6 = YES*
enables IPv6 operation on the print server. Select NO to disable IPv6 operation.
●
POLICY
=<option> allows you to select one of the following IPv6 addressing policies for the
print server.
●
RTR_AV
: (default) The stateful auto-configuration method to be used by the print
server is determined by a router. The router specifies whether or not the print server
is to obtain its address, its configuration information, or both from a DHCPv6 server.
●
RTR_UN
: If a router is not available, the print server should attempt to obtain its stateful
configuration from a DHCPv6 server.
●
ALWAYS
: Whether or not a router is available, the print server will always attempt to
obtain its stateful configuration from a DHCPv6 server.
●
MANUAL
=
KEEP
/
DISABLE
specifies the behavior for a manually-configured IPv6 address
detected on the print server.
●
KEEP
: (default) If configured, maintain the address in an active state.
●
DISABLE
: If configured, maintain the address but in an inactive state.
Print a Jetdirect configuration page to verify your settings. However, note that the print server
may overwrite selected parameters with values that ensure proper operation.
CFG IPX/SPX
Selects whether you want to access the IPX/SPX menu and set IPX/SPX protocol parameters.
NO
(default): Bypass the IPX/SPX menu items.
YES
: Access the IPX/SPX menu items.
In the IPX/SPX menu, you can specify the
Frame Type
parameter used on your network.
●
AUTO
(default) will automatically set and limit the frame type to the first one detected.
●
For Ethernet cards, frame type selections include EN_8023, EN_II, EN_8022, EN_SNAP.
WEB
For configuration management, specify whether the embedded Web server will accept
communications using HTTPS (Secure HTTP) only, or both HTTP and HTTPS.
HTTPS
: For secure, encrypted communications, only HTTPS access is accepted. The print
server will appear as a secure site.
HTTP/HTTPS
: Access using either HTTP or HTTPS is permitted.
Table C-2
HP Jetdirect EIO Menu on Classic Control Panel (continued)
ENWW
Jetdirect EIO Menus for Classic Control Panels 179
Содержание 635n - JetDirect IPv6/IPsec Print Server
