horsch Focus 4 TD Скачать руководство пользователя страница 71

Страница: 71 / 108

60059040 • 02 • 07/2021 • en

8 Row spacing

On the Focus TD the ow spacing can be altered. The row spacing can be taken from
the tables under Technical Data.

There are two options:

• Coulter extension

For the tighter row spacing, additional TurboDisc coulters are bolted to the seed
bar.

• Additional coulter bar

The Focus TD is equipped with two coulter rails, one with tight and one with
wide row spacing.

Conversion of the number of rows

The hose installation is in any case prepared for the full coulter equipment. If only
half the coulter equipment is used, two hoses each care connected to one seed
coulter. The hoses are in this case connected with Y-unions.

Y-unions on the seed coulters

For extending the coulter equipment, every second coulter must be installed.

Remove the Y-unions, connect one hose to the already present coulter, con-
nect the other hose to the newly installed coulter.

Proceed in reverse order when converting from full to half the coulter equip-
ment.

Half the coulter equipment – Focus 6 TD (series equipment)

Full coulter equipment – Focus 6 TD (option)

Содержание Focus 4 TD













































































































Результаты поиска

Содержание Focus 4 TD

Отзывы:

horsch Focus 4 TD, Руководство по эксплуатации, Страница: 71 / 108

Результаты поиска

Содержание Focus 4 TD

Отзывы: