horsch Focus 4 TD Скачать руководство пользователя страница 20

Страница: 20 / 108

2 | Safety and responsibility

60059040 • 02 • 07/2021 • en

2.9 Safety stickers

Safety stickers on the machine warn of hazards at dangerous points and are an im-
portant part of the safety equipment of the machine. Missing safety stickers increase
the risk of severe or even fatal injuries.

1. Clean soiled safety stickers.

2. Damaged or illegible safety stickers must be replaced immediately.

3. Affix the specified safety stickers on spare parts.

00380054

No passengers are allowed to ride on the machine!

00380055

Before commissioning the machine the operating instruc-
tions must be read and followed!

00380133

Caution for fluids spraying out under high pressure, follow
the notes in the operating instructions!

00380134

Never reach into areas where there is a risk of crushing as
long as parts could still be moving!

Содержание Focus 4 TD













































































































Результаты поиска

Содержание Focus 4 TD

Отзывы:

horsch Focus 4 TD, Руководство по эксплуатации, Страница: 20 / 108

Результаты поиска

Содержание Focus 4 TD

Отзывы: