horsch Focus 4 TD Скачать руководство пользователя страница 103

Страница: 103 / 108

Care and maintenance | 12

60059040 • 02 • 07/2021 • en

103

12.2 Clean the machine

Clean the machine thoroughly at regular intervals and after the end of the sea-
son.

Wear the necessary protective outfit when performing any work to protect
your health and safety.

Clean the outside of the machine with water. Open the fall sluice under the
metering unit so that entered water can flow off.

Clean the volume metering unit, distributor and hoses of the pneumatic sys-
tem, leave the fall sluice open for drying.

Clean the rotors inside the metering unit with a brush and compressed air.

Blow out coulters, seed lines, seed hopper, metering unit and fan with com-
pressed air.

Flush the components thoroughly after using solid fertiliser. Fertiliser is very
aggressive and causes corrosion.

NOTE

Do not clean electrical components, hydraulic cylinders and bearings with a
high pressure cleaner or direct water jet.
Housings, screw fittings and bearings are not waterproof under high pressure.

Spray the bearings of the DiscSystem with penetrating oil after cleaning and
before extended idle times.

Before taking back into service turn the discs by hand and check for free rota-
tion.

Clean every day when in use.

12.3 Machine storage

The following steps must be followed if the machine is to be shut down for a longer
period of time:

1. Park the machine in a hall or under a roof if possible.

2. Secure the machine with wheel chocks against rolling away.

3. Loosen the parking brake, if so equipped, to prevent the brake pads from

sticking.

4. Protect the machine against corrosion. Use only biodegradable oils for anti-

rust spraying.

5. Protect the hydraulic cylinder piston rods against corrosion.

6. Relieve the wheels from any load.

7. Completely empty and clean the seed and fertiliser hopper.

8. Reduce the coulter pressure adjustment to relieve the rubber elements.

9. Open the clearing valve.

10. Unplug the terminal and store it in a dry place.

Содержание Focus 4 TD













































































































Результаты поиска

Содержание Focus 4 TD

Отзывы:

horsch Focus 4 TD, Руководство по эксплуатации, Страница: 103 / 108

Результаты поиска

Содержание Focus 4 TD

Отзывы: