horsch Focus 4 TD Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 108

horsch Focus 4 TD Скачать руководство пользователя страница 45

Assembly groups | 6

60059040 • 02 • 07/2021 • en

45

Maintenance

Ø

Check bearings for wear.

WARNING

Danger of severe injuries caused by the tensioned spring assembly.

Ø

Never stand in front of the tines!

Ø

Replace the spring assembly only as a complete unit (workshop work).

Ø

Never open the spring assembly.

Ø

If a tine is blocked or jammed by stones etc., please contact the HORSCH Ser-
vice. The blockage may give way and the tine jump forward into its normal
position.

Adjusting the fertiliser
placement

The fertiliser depot can be placed either on the surface of the field or in the soil.
In addition to this, fertiliser can also be placed half in the soil and half on the sur-
face.

Spring flap to adjust the fertiliser placement

1. Press the spring flap together and let it engage at the desired position.

2. Adjust the flaps on all tines equally.

Three positions of the spring flap
1

Placement in the soil

2

Placement on the field surface

3

Placement in the soil and on the field surface

«
...
43
44
45
46
47
...
»

Содержание Focus 4 TD













































































































Отзывы:

Нет отзывов