horsch Focus 4 TD Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 108

horsch Focus 4 TD Скачать руководство пользователя страница 67

Operation | 7

60059040 • 02 • 07/2021 • en

67

Fan 1

7.4.2 Checks

The working quality essentially depends on the adjustments and checks made prior
to and during use, as well as on regular care and maintenance of the machine.

Ø

Carry out all maintenance tasks and adjustments before starting to work.

NOTE

Ø

Check the placing quality (drilling depth, length and transverse distribution of
the seed) on all coulters when starting work and for larger fields also in
between.

NOTE

Ø

Perform checks when starting work and with larger fields also regularly in
between!

Machine

Ø

Have the hydraulic lines been connected without being mixed up by mistake?

Ø

Has the machine been levelled in working position?

Ø

Are all cultivation tools in serviceable condition?

Ø

Has the drilling depth been set correctly?

Pneumatic system /
Hydraulics

Ø

Are all air lines between fan and coulters leak tight and firmly connected?

Ø

Are the seed hoses free of sagging, water and other deposits?

Ø

Does air flow uniformly out of all coulters?

Ø

Has the air volume been set correctly on the fan? Does the seed bounce out of
the seed furrow, or remain in the pipes and cause blockage?

Ø

Is the air separator on the head free of blockage and deposits?

Ø

Are the motor flaps installed in the correct seed lines for the tramlines?

Ø

Has the tram line rhythm been adjusted and do the flaps close?

Ø

Have all hydraulic lines been connected without being mixed up?

Pneumatic system – fan

Ø

Is the hydraulic fan connected to a pressure-free return flow?

Ø

Are the fan and intake grille clean?

Ø

Is the fan wheel tightly mounted on the shaft?

Ø

Are fan speed and drive pressure not exceeded?

«
...
65
66
67
68
69
...
»

Содержание Focus 4 TD













































































































Отзывы:

Нет отзывов