horsch 420016020001 Скачать руководство пользователя страница 57

Страница: 57 / 84

Omnis FT Owner’s Manual – Ver. 2.0 06/2020

www.horsch.com

SCH

Hydraulic Colored Markings:

Hydraulic circuits are identified by symbols or decals on the hose holder

brackets additionally marked with colored caps or handles to avoid

mixing up by mistake.

1 – Front Hitch / Rear Axle Lift (Green)

2 – Rolling Baskets (Red)

3 – Jack (Black)

4 – Fold (Yellow)

Field Operating Instructions

Entering Field:

1. Turn the Selector Valve

‘ON’

for Field Mode.

2. Raise machine

(1)

completely on front hitch cylinder and rear axle.

3. Remove the yellow safety stops from the rear axle cylinders (x2).

4. Remove any necessary front hitch cylinder depth stops.

Rolling Baskets

Rolling Baskets are an option as a rear finishing system for the Omnis

FT tillage machine. The hydraulic circuit can be operated multiple ways

based on field conditions and desired field finish:

1. Up – Retract cylinders to hold the baskets above ground for

wet/cohesive soils or when soil consolidation is not required.

2. Float – Place SCV

(2)

in to float position to allow baskets to

follow contour of ground when a light field finish is required in

fine soils.

RECOMMENDED SETTING!

CAUTION! ROLLING BASKETS CANNOT BE OPERATED

WHEN TOUCHING THE GROUND WITH HYDRAULIC

CIRCUIT

(2)

IN NEUTRAL POSITION. PREMATURE

FAILURE MAY OCCUR TO BASKET COMPONENTS AND

WILL VOID FACTORY WARRANTY!

With cohesive soils the baskets may accumulate material

and become considerably heavier. This can overload

components of the machine, creating difficulties folding

wings, and/or create a hazard on the roads during

transportation. Therefore, rolling baskets must always be

cleaned before road transportation if they have picked up

material.

Содержание 420016020001





















































































Результаты поиска

Содержание 420016020001

Отзывы:

Похожие инструкции для 420016020001

Бренды по названию

Популярные бренды

horsch 420016020001, Руководство пользователя

Результаты поиска

Содержание 420016020001

Отзывы:

Похожие инструкции для 420016020001

Бренды по названию

Популярные бренды