horsch 420016020001 Скачать руководство пользователя страница 28

Страница: 28 / 84

28 Omnis FT Owner’s Manual – Ver. 2.0 06/2020

www.horsch.com

SCH

Wear Protective Clothing
Protective Clothing

For operation and maintenance of this machine, you will need:

•

Snug fitting clothing; no loose articles or strings.

•

Safety gloves and goggles to protect against dirt and sharp-edged machine

parts.

Use a Safety Chain

A safety chain will help control drawn equipment should it accidentally separate from the drawbar. A

safety chain of the proper strength rating is provided with the machine as standard equipment.

Using the appropriate adapter parts, attach the chain to the tractor drawbar support, seed wagon rear

hitch support, or other specified anchor location. Provide only enough slack in the chain to permit turning.

Road Traffic Safety

The valid road traffic regulations are to be observed when traveling on public roads, paths, and areas.

Do not exceed the maximum permissible transportation widths and heights and install road lighting

equipment, warnings and safety covers where necessary.

Do not exceed the permissible axle loads, tire carrying capacities and total weights, in order to ensure

sufficient steering and braking capabilities. Handling is affected by the implement connected. It is

important to consider the large overhang and the centrifugal mass of the implement, particularly when

cornering.

DO NOT EXCEED A MAXIMUM SPEED OF 20 MPH DURING TRANSPORTATION. LOSS

OF VEHICLE/MACHINE CONTROL CAN RESULT IN SERIOUS PERSONAL INJURY OR DEATH!

The whole machine is to be cleaned of soil that has been collected before travel on public roads. Be sure

to thoroughly clean the debris from the rear Rolling Basket packer system.

Do not travel on roads with the rear Rolling Basket packer system on the

ground. This may cause damage to the roads and premature wear and

possible malfunction of components to the machine.

Passengers are strictly forbidden to ride on the machine.

Содержание 420016020001





















































































Результаты поиска

Содержание 420016020001

Отзывы:

Бренды по названию

Популярные бренды

horsch 420016020001, Руководство пользователя

Результаты поиска

Содержание 420016020001

Отзывы:

Бренды по названию

Популярные бренды