Honeywell XLS80e Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 138

background image

116

Honeywell, Issue 9
March 2007

XLS80e Fire Alarm Control Panels

14 Master/Slave Network

This section describes how to configure the
panel for use with a Master/Slave network only.
It does

not

describe the XLSNET peer-to-peer

network - refer to the XLSNET

Appendix 3

for

information about this alternative network.

A panel cannot simultaneously be attached to
both types of network. However, if it is on the
XLSNET network, the Master/Slave network
can still be used for repeaters as described in
the XLSNET manual.

14.1 Introduction

The XLS80e Series control panels can work
either as stand-alone units or networked with
other control panels and repeaters. When
networked, each control panel supervises its
own detection system of up to eight loops of
sensors and modules. It then functions
independently of all other panels.

An RS485 communication system enables
events at any panel to be relayed to all other
panels and repeaters, causing appropriate
annunciations and/or actions at those panels
or repeaters.

14.1.1 Number of Stations on Network

The network consists of one Master panel, a
number of Slave panels and (optional) a
number of Repeaters.

The term ‘Station’ is used to refer to the Master
panel, a Slave panel and a Repeater. The
network has a maximum of 32 stations.
Restrictions on the number of Slave panels
and Repeaters are detailed below.

14.1.1.1

Panels

Each Network must include

one

(and only one)

Master panel. This panel has overall control
of the network. It receives all networked
messages from the Slave panels and its
configuration determines how these are acted
upon and redistributed.

The network may also include up to

seven

Slave panels. These panels have independent
control of their own local loops, and report any
local events to the Master panel.

The Master/Slave

network does not

provide the transmission

path integrity required

by EN54-2: 12.5.3

«
...
121
122
123
124
125
...
»

Содержание XLS80e











































































































































Отзывы:

Нет отзывов

Похожие инструкции для XLS80e

Бренд: Rayrun Страницы: 2

Бренд: IDenticard Страницы: 2

Бренд: 3Ware Страницы: 2

Бренд: B meters Страницы: 2

Бренд: Hanna Instruments Страницы: 54

Бренд: Hanna Instruments Страницы: 2

Бренд: IDK Страницы: 96

Бренд: jablotron Страницы: 22

Бренд: jablotron Страницы: 2

Бренд: RAM Страницы: 32

Бренд: Rain Bird Страницы: 20

Бренд: Ban Seok Страницы: 9

Бренд: Data Signs Страницы: 23

Бренд: Warner Electric Страницы: 4

Бренд: SYCLOPE electronic Страницы: 40

Бренд: Timotion Страницы: 10

Бренд: Aeta Audio Systems Страницы: 24

Бренд: Reer Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды