Honeywell OW-CDX050 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 134

background image

R110

OneWireless Multinode User's Guide

23

6/08

Installation Overview

First read through this section so that you have a good understanding of the tasks to
properly plan and execute installation of Multinode/WSG nodes in a wireless network.

Preinstallation requirements

The following tasks must be completed before you actually install wireless system
gateways and multinodes in a wireless network:

•

Network site planning

must be completed to understand how a wireless network

can be built and supported for your application using OneWireless components.
These components consist of wireless field devices, multinodes, and wireless system
gateways.

•

RF site survey

must be completed by a qualified professional. The RF survey is

essential for building the architecture of the wireless network. The site survey should
at a minimum include the following tasks:

−

RF spectrum analysis must be conducted on the 2.40-2.49 GHz band and 5.7-5.9
GHz band (if available to be used) to detect any potential RF interference.
Strong interference sources should be addressed (removed, avoided or
minimized) before an installation. Note that some frequencies may not be
available for use in some locations and countries.

−

A point-to-point 2-node mesh should be staged in various locations to measure
the RF propagation ability in the site environment. Received Signal Strength
Indicator (RSSI) can serve as one indicator of the RF environment. TCP/IP
throughput testing and UDP/IP throughput and packet drop rate testing should
be conducted in all selected locations to measure the quality of the site
environment.

−

Site survey should be conducted once the factory system is operating so that
maximum possible interference is measured and addressed.

•

Multinode placement

should be determined through the completion of the network

planning and RF survey activities.

•

Power requirements

for network should be identified. Wired cable runs that

provide DC power to the WSGs and multinodes should be determined.

•

Ethernet cable runs

should be determined for WSGs and/or any other wired nodes

in the network.

«
...
33
34
35
36
37
...
»

Содержание OW-CDX050







































































































































Отзывы:

Нет отзывов

Похожие инструкции для OW-CDX050

Бренд: BAPI Страницы: 4

NETWORK INTERFACE CARDS

Бренд: Secure Computing Страницы: 17

SureCross Performance FlexPower DX80G9M2S-P7

Бренд: Banner Страницы: 10

easyconnect ec350

Бренд: Netbiter Страницы: 40

Бренд: Dinstar Страницы: 100

WPC-832-2-Modbus-MQTT

Бренд: KSH International Страницы: 16

Бренд: Ubee Страницы: 103

Бренд: XLOCK Страницы: 2

Babel Buster Pro V210

Бренд: CONTROL SOLUTIONS Страницы: 2

Бренд: Fanvil Страницы: 48

Бренд: Voptel Technology Страницы: 67

Бренд: GRASS VALLEY Страницы: 210

Бренд: Cooper Atkins Страницы: 21

Бренд: Innbox Страницы: 12

Бренд: 2N Страницы: 9

Бренд: 2N Страницы: 57

Бренд: 2N Страницы: 67

Бренд: Sensus Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды