Honeywell OW-CDX050 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 134

background image

The Multinode/Wireless System Gateway

Multinode specificiations

R110

OneWireless Multinode User's Guide

21

6/08

•

One field I/O radio which communicates with the various wireless field devices. A
multinode will contain one of two radio types:

−

A FHSS radio which uses Frequency Hopping Spread Spectrum modulation as
the communications protocol.

−

A DSSS radio which uses a Direct Sequence Spread Spectrum modulation as the
communication procotol and is based on the IEEE 802.15.4 standard.

Antennas

The multinode is supplied with three 5dBi omni-directional antennas. Two antennas are
identical and are installed to the MESH and AP connectors located on the top of the unit.
These antennas are used with the 802.11 radios for client and wireless mesh
communications. The third antenna is used with the field I/O radio for communication
with the field devices and is installed on the FIELD I/O ANTENNA (or FHSS
ANTENNA) connector.
Note: The 802.11 antennas and the field I/O radio antenna are not interchangeable.

A number of optional high gain antennas from various manufacturers also have been
qualified for use with the multinode.  Antenna selection is based on a number of factors
such as frequency range, overall antenna output, and country regulations.  Antenna
options also include installation of the antenna remote from the multinode. When using
one of these antennas, you must manually adjust the transmit power of the radios in the
multinode.

ATTENTION

Multinodes must be professionally installed in accordance with the
requirements specified in the

OneWireless Multinode Agency Compliance

Professional Installation Guide

.

If you are not using the wireless access point function then you do not need to connect
the client antenna. Make sure during your configuration set up that you go to the

Wireless Access Point-General

screen and set the Tx Pwr Mode to Off, (See page 47).

Also ensure that any unused antenna port is securely covered with the attached protection
caps.

NOTE: If any part of the multinode or antenna is located outdoors, a lightning arrestor
must be installed between the unit and the antenna. See the

Outdoor protection kit

.

«
...
31
32
33
34
35
...
»

Содержание OW-CDX050







































































































































Отзывы:

Нет отзывов

Похожие инструкции для OW-CDX050

Бренд: Patton electronics Страницы: 2

Бренд: Ideal Life Страницы: 16

ServiceRouter V2

Бренд: Eurogard Страницы: 23

Бренд: Duemmegi Страницы: 11

Intesis IN701-KNX Series

Бренд: HMS Networks Страницы: 48

UNIGATE IC - Powerlink

Бренд: DEUTSCHMANN AUTOMATION Страницы: 50

KoolKey EKA 200

Бренд: Danfoss Страницы: 2

Бренд: Geneko Страницы: 158

Бренд: Velleman Страницы: 84

Бренд: King Pigeon Страницы: 52

Бренд: King Pigeon Страницы: 55

TOOLBOX-ETH-GPRS

Бренд: Ewattch Страницы: 14

Бренд: San Telequip Страницы: 20

Optimizer Voice

Бренд: RedPort Страницы: 18

Бренд: Planet Страницы: 162

Бренд: Wildix Страницы: 5

Бренд: Wildix Страницы: 15

Бренд: ZyXEL Communications Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды