Honeywell OW-CDX050 Скачать руководство пользователя страница 6

Страница: 6 / 134

About This Document

Symbol Definitions

OneWireless Multinode User's Guide

R110

6/08

Symbol Definitions

The following table lists those symbols used in this document to denote certain conditions.

Symbol Definition

ATTENTION:

Identifies information that requires special

consideration.

TIP:

Identifies advice or hints for the user, often in terms of

performing a task.

CAUTION

Indicates a situation which, if not avoided, may result in equipment
or work (data) on the system being damaged or lost, or may result in
the inability to properly operate the process.

CAUTION

: Indicates a potentially hazardous situation which, if not

avoided, may result in minor or moderate injury. It may also be used
to alert against unsafe practices.

CAUTION

symbol on the equipment refers the user to the product

manual for additional information. The symbol appears next to
required information in the manual.

WARNING

: Indicates a potentially hazardous situation, which, if not

avoided, could result in serious injury or death.

WARNING

symbol on the equipment refers the user to the product

manual for additional information. The symbol appears next to
required information in the manual.

Содержание OW-CDX050







































































































































Результаты поиска

Содержание OW-CDX050

Отзывы:

Honeywell OW-CDX050, Руководство пользователя, Страница: 6 / 134

Результаты поиска

Содержание OW-CDX050

Отзывы: