Honeywell OW-CDX050 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 134

background image

R110

OneWireless Multinode User's Guide

3

6/08

OneWireless System

Overview

OneWireless is Honeywell’s network solution which connects process sensors and
transmitters to the control system wirelessly in an industrial control environment.
OneWireless uses Radio Frequency (RF) communications to transfer process data
between the sensors and the control system, rather than the traditional wired connections.

WNSIA solution

There are four major components that make up Honeywell’s OneWireless network:

1.

Wireless sensors (field I/O devices, such as temperature or pressure transmitters) that
provide replacement for non-electronic or legacy wired sensors.

2.

Wireless network infrastructure nodes (Multinodes) that serve as the network
backbone to route wireless traffic towards the gateway and the control system.

3.

Wireless System Gateways (WSGs) which act as bridges between the wireless
network and the wired plant network.

4.

Wireless device configuration tools (Wireless Builder, Key Server, Network
Management and Diagnostics) allow users to configure, operate and monitor
wireless devices.

A typical OneWireless network using these components is shown in Figure 1.

«
...
13
14
15
16
17
...
»

Содержание OW-CDX050







































































































































Отзывы:

Нет отзывов

Похожие инструкции для OW-CDX050

Бренд: Banner Страницы: 96

Бренд: Yeastar Technology Страницы: 11

Network Device P-2302

Бренд: ZyXEL Communications Страницы: 359

Бренд: Aaeon Страницы: 26

Бренд: EAE Страницы: 22

M2M CONTROL CX660

Бренд: Infranet Technologies Страницы: 44

Бренд: D-Link Страницы: 83

Бренд: NEP Страницы: 6

Бренд: Netphonic Страницы: 36

Cayman 3500 Series

Бренд: Netopia Страницы: 2

Бренд: Netopia Страницы: 2

NETSCAPE DIRECTORY SERVER 7.0

Бренд: Netscape Страницы: 178

Babel Buster Pro V210

Бренд: CONTROL SOLUTIONS Страницы: 2

Бренд: 2Wire Страницы: 30

Бренд: 2Wire Страницы: 2

Бренд: Technicolor Страницы: 58

Бренд: Bang & Olufsen Страницы: 62

PathBuilder S200 Series

Бренд: 3Com Страницы: 162

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды