Honeywell OW-CDX050 Скачать руководство пользователя страница 31

Страница: 31 / 134

The Multinode/Wireless System Gateway

Multinode specificiations

R110

OneWireless Multinode User's Guide

6/08

LED Indicator

When lit it …

with the gateway application and the WSG has been
configured in Wireless Builder.

•

Multinode - LED behavior is undetermined.

NOTE: A fault in the multinode is indicated when WLAN1 and WLAN2 LEDs blink
simultaneously. The multinode software has detected a fault with the encryption
algorithm or the device configuration has not passed the integrity check. See

Troubleshooting

for more information.

Multinode specificiations

Table 3 Multinode specifications

Specification

Description

Enclosure

Certifications: Class 1 DIV2/ZONE2 hazardous area.

IP66 waterproof

Physical dimensions: 9.25 in. x 8.25 in. x 3.0 in.

Weight: 7.0 lbs

Power requirements

Power input: +24 Volts dc, -15% +10% (20.4 to 26.4Vdc)

Current requirement: 1.5 Amps, maximum.

Power output: 25 Watts, maximum

Hardware Specification:

CPU: XScale IXP425 @ 533 MHz

8 MB flash

64 MB SDRAM

External Ports:

Two 10/100 Mbps WAN Ethernet ports. See Note.

3 external antenna ports.

Note: Both Ethernet ports are wired to one switch with a
single MAC Address.

WAN Ethernert setting:

Fixed IP

Supports: IEEE 802.3u Fast Ethernet

Содержание OW-CDX050







































































































































Результаты поиска

Содержание OW-CDX050

Отзывы:

Honeywell OW-CDX050, Руководство пользователя, Страница: 31 / 134

Результаты поиска

Содержание OW-CDX050

Отзывы: