Honeywell OW-CDX050 Скачать руководство пользователя страница 29

Страница: 29 / 134

The Multinode/Wireless System Gateway

Physical description

R110

OneWireless Multinode User's Guide

6/08

Table 1 Multinode connections

Feature or Connector

Description

ETHERNET
24V DC POWER

¾-inch conduit connection with four cable pigtails.

•

Two Ethernet cables - (Labelled WLAN1 and
WLAN2) Either Ethernet cable can be used to:

−

Connect to a PC for initial setup.

−

Connect the WSG to the plant control
network

−

Connect Ethernet-based devices, such as
switches, controllers, cameras, etc. to a
multinode or WSG.

Note: Both Ethernet ports are wired to one switch
with a single MAC Address.

•

A red (or grey) cable - power cable

•

A green/yellow grounding conductor.

IR PORT

Infrared sensor port used for communication with the
authentication device.

FHSS ANTENNA

(Type N-female connector)

FIELD I/O ANTENNA

(Type N-female connector)

Provides connection of an omni-directional antenna or
optional remote antennas for communication with
various wireless field devices.

ANTENNA

(Two reverse polarity
Type N-female connectors)

AP ANTENNA

and

MESH ANTENNA

(Two Type
N-female connectors)

Provides connection for two 5dBi omni-directional or
optional remote antennas that enable communication
between the multinodes, WSGs, other multinodes in
the network and other WiFi devices.

Operating/Status indicators
LEDs

Six indicators located on the top of the multinode
enclosure and indicate operating status. These LEDs
are described in Table 2 on page 18.

Содержание OW-CDX050







































































































































Результаты поиска

Содержание OW-CDX050

Отзывы:

Похожие инструкции для OW-CDX050

Бренды по названию

Популярные бренды

Honeywell OW-CDX050, Руководство пользователя

Результаты поиска

Содержание OW-CDX050

Отзывы:

Похожие инструкции для OW-CDX050

Бренды по названию

Популярные бренды