Honeywell OW-CDX050 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 134

background image

Installation Overview

Multinode/WSG installation

30

OneWireless Multinode User's Guide

R110

6/08

ATTENTION

The power cable attached to the multinode may be one of the following:

•

Red cable with two wires (Red and Black)

•

Grey cable with two wire pairs (Red and Green, Black and White)

The red (or grey) power cable, the Green/yellow grounding cable and Ethernet cables are
connected as follows:

Step

Action

1

Ensure that all power is removed from the power cabling run to the multinode
site.

2

If the multinode is equipped with a Red power cable:

•

Connect the Red wire from the multinode power cable to +24 volt dc output
of the power supply in the junction box.

•

Connect the Black wire from the multinode power cable to the 24 volt
COMMON of the power supply.

If the multinode is equipped with a Grey power cable:

•

Connect both the Red and Green wires from the multinode power cable to
+24 volt dc output of the power supply in the junction box.

•

Connect both the Black and White wires from the multinode power cable to
the 24 volt COMMON of the power supply.

3

Cut and tie back the drain wire from the power cable.

4

Connect the Green/Yellow grounding cable from the multinode to a safety
ground point.

5

The two WAN cables, labeled WLAN1 and WLAN2 (Ethernet cables), from
the multinode are configured with the same IP address and a single MAC
address and should be regarded as a two-port Ethernet switch. Therefore, if
the control system provides connections to redundant switches, then use
both Ethernet cables to connect to the separate switches.

If only a single switch available in the control system, then use WLAN1
Ethernet cable to connect to the network switch. The two Ethernet cables
should not be connected to the same network switch.

Note: Using the WLAN1 cable enables the the WLAN LED indicator.

«
...
40
41
42
43
44
...
»

Содержание OW-CDX050







































































































































Отзывы:

Нет отзывов

Похожие инструкции для OW-CDX050

OFFICESERV 7100

Бренд: Samsung Страницы: 97

OfficeConnect 3C855

Бренд: 3Com Страницы: 4

Бренд: TRENDnet Страницы: 4

Бренд: Elpro Technologies Страницы: 164

Бренд: Quadro Страницы: 54

Бренд: Rath Страницы: 9

Бренд: Telco Страницы: 28

Бренд: ProSoft Страницы: 157

Бренд: Zipato Страницы: 36

Бренд: XAVi Страницы: 51

Бренд: Ursalink Страницы: 25

Бренд: Innovaphone Страницы: 24

Бренд: Technicolor - Thomson Страницы: 52

Бренд: MOKO Страницы: 34

Бренд: Pahlen Страницы: 19

Бренд: Omron Страницы: 11

Бренд: Omron Страницы: 78

Бренд: SELECTRONIX Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды