Hologic SUROS ATEC Emerald Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 48

background image

ATEC

Pearl, ATEC Sapphire and ATEC Emerald

Breast Biopsy and Excision System

29

This document contains information that is confidential and proprietary to Suros Surgical Systems, Inc., a Hologic company. The document
and/or information contained herein may NOT be disclosed to any party without the express written consent of Suros. Covered by one or more of
the following patents and other patents pending: 6,758,824 and 6,638,235. © 2007 Suros Surgical Systems, Inc ATEC, Suros and Suros
Compassionate Technologies are trademarks or registered trademarks of Suros in the United States and other countries. All rights reserved.

LIT309:RevB

Replacing the Compressor Muffler
1.  Use a strap wrench to remove the compressor muffler.
2.  Discard used muffler.
3.  Apply a thin layer of HVAC Blue Compound onto the new Muffler NPT threads.

Ensure you remove all old sealant from NPT threads.

4. Hand-tighten into the middle port of the Brass Union “T”.

Removing the Vacuum Pump
1.  Remove the Compressor if not already removed.
2.  Unscrew the nut on the front left leg of the vacuum pump with an 11/32” wrench.
3.  Loosen and remove all 4 screws on the vacuum pump with a 9/64” hex bit.
4.  Disconnect the black and white power cables (use needle nose pliers).
5.  Snip cable ties by green grounding wire.
6.  Remove the vacuum pump.

Replacing the Vacuum Pump Mounts
1. Remove the old 4 mounts with a 5/64” Allen wrench and 5/16” socket.

a. Discard old mounts.

2. Inset new mounts, with the long rubber part of the mount up.

a. Secure with 2 screws (SR6291-01) through each mount.
b. Secure each screw with an external tooth lock washer (SR6290-01) and a nut

(SR6289-01) on the underside of the baseplate.

c. Torque to 24 in/lbs using a 5/64” Allen wrench and 5/16” socket.

Replacing the Compressor Mounts
1. Remove the mounts with a 5/32” Allen wrench and an 11/32” socket.

a. Discard old mounts.

2. Inset new mounts, with the long rubber part of the mount up.

a. Secure with 2 screws (SR6292-01) through each mount.
b. Secure each screw with an external tooth lock washer (SR6225-01) and a nut

(SR6232-01) on the underside of the baseplate.

c. Torque to 30 in/lbs using a 5/32” Allen wrench and an 11/32” socket.

Reinstalling the Vacuum Pump
1. Install the vacuum pump assembly onto the vibration isolators in the back of the

baseplate.

2. The muffler will be on the left side.
3. Secure with 3 screws (SR6257-01) and 1 long screw (SR6214-01), 4 Lord snubbing

washers (SR6202-01), 4 (SR6180-01) snubbing washers, and 4 lock washers
(SR6234-01).

a. The long screw (SR6214-01) secures the vacuum pump leg on your left and at

the front.

b. Liberally apply Cement Adhesive (SR6294-01) to first 4-5 threads of all screws.

4. Insert 1 (SR6202-01) Lord Snubbing Washer between the top of each mount and the

vacuum pump.

5. Insert 1 (SR6180-01) Snubbing Washer between the lock washer and the bottom of

each mount.

«
...
28
29
30
31
32
...
»

Содержание SUROS ATEC Emerald

















































Отзывы:

Нет отзывов

Похожие инструкции для SUROS ATEC Emerald

AJSPD850P - P2 DECK

Бренд: Panasonic Страницы: 73

Бренд: Cannon Страницы: 40

Бренд: NARGESA Страницы: 34

Бренд: ICELED Страницы: 4

Бренд: Facom Страницы: 4

Бренд: FaceLake Страницы: 2

Бренд: Federal Signal Corporation Страницы: 4

Бренд: ParaBody Страницы: 7

Pressure Governor

Бренд: Waterous Страницы: 53

Бренд: Landi Renzo Страницы: 16

Бренд: IBM Страницы: 163

Бренд: RBC Bioscience Страницы: 24

Бренд: S&C Страницы: 16

Бренд: S&C Страницы: 23

2261998USBA1-XX

Бренд: MMF POS Страницы: 5

Бренд: Hedson Страницы: 32

Бренд: JLG Страницы: 165

Бренд: Labconco Страницы: 174

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды