Hochiki HCP 1000 Series, Инструкция по установке и эксплуатации

Страница: 43 / 54

Page 41 of 52
10.7 CONFIGURING FEATURES:
The re are two types of Features; those which are just turned ON and OFF, and those with Multiple Settings. For ON
and OFF Features , the Yellow LED is lit for ON, and not lit for OFF, and the Yellow Button is pressed to change the
ON / OFF setting. For Multiple Setting Features , the Yellow LED flashes a number of times to indicate the setting,
then pauses; the Yellow Button is used to change the selected setting. Be sure to pause for about 3 seconds after
changing the Configuration DIP Switches , or pressing the Yellow Button to see the results.
DIP SWITCH
POSITION (1-8)
FEATURE DESCRIPTION
0000 0001 Style D/B (Class A/B) Initiating Circuits Yellow LED lit indicates that all Initiating Circuits (Detection
Zones) are Style D (Class A), off indicates that they are all Style
B (Class B). This Feature can be checked at any time, but must
only be changed as described in
Restore to Default .
0000 0010 Manual Signal Silence Enable Yellow LED lit indicates that Manual Silence is enabled.
0000 0011
Fire Drill Enable
Yellow LED lit indicates that Fire Drill is enabled.
0000 0100 Two Stage Operation Enabled Yellow LED lit indicates that the System is set for Two Stage
operation, and not lit indicates Single Stage operation.
0000 0101
Common Alarm Relay Operation
Yellow LED lit indicates that if the System is for Two Stage
operation, the Common Alarm Relay will only operate during the
General Alarm Stage. If not lit, the Common Alarm Relay will
operate during both Stages.
0000 0110
Output Circuit Correlations Enabled
Yellow LED lit indicates that Output Circuits (Indicating Circuits
and Relays) operate according to any set Correlations (see
Correlation section). If the
Yellow LED is not lit, all Output
Circuits are Common Alarm; all outputs turn on for any Alarm
Input.
0000 0111
Waterflow & Sprinkler Retard Operation
Yellow LED lit indicates that Waterflow Retard is enabled.
0000 1000 Reserved for Future Use
0000 1001 Aux Disc & Programmable Relays Yellow LED lit indicates that Correlated Relays are disconnected
by Auxiliary Disconnect.
0011 1000 Show Relay Circuits All Display Points assigned to Relay Circuits will be lit.
0000 1010
Signal Silence Inhibit Timer Yellow LED does not flash = Disabled
Yellow LED flashes 1 time = 1 minute
Yellow LED flashes 2 times = 2 minutes
Yellow LED flashes 3 times = 3 minutes
0000 1011
Auto Signal Silence Timer
(This timer cannot be set shorter than either
the Auto General Alarm or Signal Silence
Inhibit timers, if those timers are enabled)
Yellow LED does not flash = Disabled
Yellow LED flashes 1 time = 5 minute
Yellow LED flashes 2 times = 10 minutes
Yellow LED flashes 3 times = 15 minutes
Yellow LED flashes 4 times = 20 minutes
Yellow LED flashes 5 times = 30 minutes
0000 1100 Auto General Alarm Timer
(Leave disabled unless the System is
configured for Two Stage operation)
Yellow LED does not flash = Disabled
Yellow LED flashes 1 time = 5 minute
Yellow LED flashes 2 times = 10 minutes
Yellow LED flashes 3 times = 15 minutes
Yellow LED flashes 4 times = 20 minutes
Yellow LED flashes 5 times = 30 minutes
0000 1101 Audible Indicating Circuit
Evacuation Code Yellow LED flashes 1 time = Continuous
Yellow LED flashes 2 times = March Time
Yellow LED flashes 3 times = Temporal Code
Yellow LED flashes 4 times = California Code
0000 1110 Number of Remote Annunciators Yellow LED flashes 0 to 8 times to indicate the number of
Remote Annunciators expected by the System.
10.8 CONFIGURING INITIATING AND INDICATING CIRCUITS:
firealarmresources.com