Hitachi NT 65A3 Скачать руководство пользователя страница 36

Страница: 36 / 45

--- 33 ---

(2) Magazine Ass'y [63], Nail Feeder [67] and the related parts

Tools required

4 mm (0.157") hexagonal bar wrench

8 mm (0.315") spanner

3 mm dia. (0.118") roll pin remover

[CAUTION] When handling the Ribbon Spring [66], wear approved eye protector without fail.

(a) Disassembly (Refer to Fig. 21.)

Ensure without fail that the Nail Feeder [67] is positioned at the Guide Plate [25] side before attempting

further disassembly.

Remove the Hex. Socket Hd. Bolt M5 x 18 [31], the Nylock Bolt (W/Flange) M5 x 8 [68] and the Nylock

Hex. Socket Hd. Bolt M5 x 12 [29]. Pull the Magazine Ass'y [63] backward while pressing the Nail Feeder

[67] against the Nose Ass'y [22], and then the Magazine Ass'y [63] and Sleeve (A) [30] can be removed.

After removal of the Magazine Ass'y [63], the Nail Feeder [67] and the Ribbon Spring [66] can be removed

by hand.

Remove the three Hex. Socket Hd. Bolts (W/Flange) M5 x 12 [69], and then the Handle Arm [61] and the

Magazine Cover [62] can be removed.

(b) Reassembly (Refer to Figs. 21, 22 and 23.)

Reassembly can be accomplished by following the disassembly procedures in reverse. However, special

attention should be given to the following points:

Tighten the Nylock Bolt (W/Flange) M5 x 8 [68] and the Nylock Hex. Socket Hd. Bolt M5 x 12 [29] for

mounting the Magazine Ass'y [63] and the Nose Ass'y [22] while pressing the Magazine Ass'y [63] against

the Nose Ass'y [22] and Body Ass'y [19]. (Press the Magazine Ass'y [63] in "A" and "B" directions as

shown in Fig. 21. Check that there is no space between the Nose Ass'y [22] and the Magazine Ass'y [63]

as shown in Fig. 22.)

Temporarily tighten the two Hex. Socket Hd. Bolts (W/Flange) M5 x 12 [69] and the Hex. Socket Hd. Bolt

M5 x 18 [31] for mounting the Handle Arm [61]. Mount the Magazine Ass'y [63] and the Nose Ass'y [22].

Perform positioning of the Handle Arm [61] to the Body Ass'y [19] so that the Hex. Socket Hd. Bolt M5 x 18

[31] for mounting them can be tightened easily, and then tighten the bolt with the specified torque.

Tighten the other bolts with the specified torque.

Содержание NT 65A3














































Результаты поиска

Содержание NT 65A3

Отзывы:

Похожие инструкции для NT 65A3

Бренды по названию

Популярные бренды

Hitachi NT 65A3, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание NT 65A3

Отзывы:

Похожие инструкции для NT 65A3

Бренды по названию

Популярные бренды