Hitachi NT 65A3 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 45

background image

--- 12 ---

(3) Control valve section

Be careful not to make mistakes in mounting the following parts that were changed for the Model NT 65A3

because these parts are similar to those of the Model NT 65A2 but not interchangeable.

O-ring (I.D 10.7)
[44] (O-ring
mounted to the
outside of the
Valve Bushing
[45])

Part

NT 65A3

NT 65A2

Caution

Inside diameter 10.7 mm

Never mount the O-ring (S12)
for the Model NT 65A2 to the
valve bushing of the Model
NT 65A3 by mistake.
Otherwise, the O-ring may be
damaged when mounting the
valve bushing to the body,
and the damaged O-ring may
cause a malfunction when
selecting the single actuation
(single sequential actuation)
mechanism.
Do not mount the O-ring (ID
10.7) for the Model NT 65A3
to the valve bushing of the
Model NT 65A2. Otherwise,
air leakage may occur.

Valve Bushing [45]

Part

NT 65A3

NT 65A2

Caution

These parts were newly

designed to provide the single

actuation (single sequential

actuation)/contact actuation

selector. They are not

interchangeable.

Plunger (B) [52]

Parts that were changed for the Model NT 65A3 and not interchangeable with those of the Model NT 65A2

(except the parts described in )

2

Cross-sectional view

Valve Sleeve [47]
(Switching device)
O-ring (P-9) [46]

Plunger O-ring
[49] (Mounted to
the inside of the
Valve Bushing
[45])

O-ring (P-9)
Wire dia. 1.9 mm
Inside dia. 8.8 mm

These parts are exclusive to

the Model NT 65A3.

Wire dia. 1.5 mm
Inside dia. 4.5 mm

1

Inside diameter 11.5 mm

1

«
...
13
14
15
16
17
...
»

Содержание NT 65A3














































Отзывы:

Нет отзывов

Похожие инструкции для NT 65A3

Бренд: D'Orly Страницы: 11

Бренд: Hitachi Koki Страницы: 52

Бренд: Hitachi Koki Страницы: 80

Бренд: Parkside Страницы: 46

Бренд: Task Force Страницы: 12

Бренд: Loctite Страницы: 14

Бренд: Parkside Страницы: 54

HandyMaster 33014

Бренд: Desa Страницы: 8

Бренд: Metabo HPT Страницы: 72

Бренд: Vulcan-Hart Страницы: 14

Бренд: Titan Страницы: 22

Бренд: REDHEAD Страницы: 11

Бренд: Haussmann Страницы: 11

Бренд: TJEP Страницы: 216

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды