background image

--- 27 ---

Tool required

    4 mm (0.157") hexagonal bar wrench

(a) Disassembly (Refer to Figs. 11, 12 and 13.)

As illustrated in Fig. 10, loosen the four Hex. Socket Hd. Bolts M5 x 20 [1], and remove the Exhaust Cover

[3].  The Piston [9] can then be taken out.

Perform the following operation first if the Piston [9] cannot be removed because the top surface of the

Piston [9] is flush with the top surface of the Cylinder [13].

Next, as illustrated in Fig. 11, screw the two previously removed Hex. Socket Hd. Bolts M5 x 20 [1] into the

provided holes on the Cylinder Plate [12].  Gripping these two bolts, simultaneously turn and pull upward to

remove the Cylinder Plate [12], the Cylinder [13] and the related parts.

If the Cylinder [13] is difficult to remove as described above, remove the Nose Ass'y [22] as described in

paragraph 10-2-(1), and push down on the cylinder to remove it from the lower portion of the main body.

(2) Piston [9], Cylinder [13] and the related parts

Washer M5 [50]

Nylon Nut M5 [60]

Body Ass'y [19]

Washer [32]

Hex. Socket Hd. Bolt M5 x 18 [31]

Roll Pin D3 x 30 [38]

Piston Bumper [21]

Plunger (B) [52]

Plunger (B) Spring [51]

Magazine Ass'y [63]

Guide Plate [25]

Nylock Hex. Socket
Hd. Bolt M5 x 16 [24]

Nose Ass'y [22]

Fig. 10

Содержание NT 65A3














































Отзывы: