Hitachi NT 65A3 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 45

background image

--- 25 ---

10. DISASSEMBLY AND REASSEMBLY

The items particularly necessary for disassembly and reassembly are described below. The [Bold] numbers in

the descriptions below correspond to the item numbers in the Parts List and exploded assembly diagram.

[CAUTION]

Before disassembly or reassembly, be sure to disconnect the air hose from the nailer (with your finger

released from the trigger) to exhaust all the compressed air and remove all nails.

10-1. General Precautions in Disassembly and Reassembly

Apply grease (ATTOLUB No. 2 Code No. 317918) to the O-rings and the sliding portions. Note that another

grease (MULTEMP PS No. 2 Code No. 939301) must be applied to the O-rings and the sliding portions of the

control valve section. Do not scratch the O-rings nor adhere dust to them when mounting.

Oil required: Hitachi pneumatic tool lubricant

1 oz (30 cc) oil feeder (Code No. 877153)

4 oz (120 cc) oil feeder (Code No. 874042)

1 quart (1 ltr) can (Code No. 876212)

If Gasket (B) [4] is damaged, replace it and check that no air is leaking.

Be especially careful to prevent the entry of foreign particles into the control valve section.

Tightening torque for each part

Screw

Tightening torque

Nylock Hex. Socket Hd. Bolt M5

Hex. Socket Hd. Bolt M5

Nylock Hex. Socket Hd. Bolt (W/Flange) M5

Hex. Socket Hd. Bolt (W/Flange) M5

85 5 kgf

•

cm

(8.3 0.5 N

•

m, 6.1 0.4 ft-lbs.)

«
...
26
27
28
29
30
...
»

Содержание NT 65A3














































Отзывы:

Нет отзывов

Похожие инструкции для NT 65A3

Бренд: Snap-On Страницы: 14

Chicago Electric Power Tools 93241

Бренд: Harbor Freight Tools Страницы: 19

Бренд: Rona Страницы: 58

Бренд: Paslode Страницы: 20

Бренд: Paslode Страницы: 32

Бренд: strapex Страницы: 36

Бренд: PNI Страницы: 19

Бренд: Porter-Cable Страницы: 13

Бренд: Northern Tool Страницы: 6

Бренд: Cocraft Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды