Hitachi NT 65A3 Скачать руководство пользователя страница 4

Страница: 4 / 45

--- 1 ---

1. PRODUCT NAME

Hitachi Finish Nailer, Model NT 65A3

2. MARKETING OBJECTIVE

The new Model NT 65A3 finish nailer is a minor-changed version of the current Model NT 65A2. To correspond to

the modification of the ANSI standard on the 1st of May 2003, the valve construction was partially changed.

In addition, the switching device (valve sleeve (A)) was provided to make the nailer operation selectable between

"single actuation (single sequential actuation) mechanism" and "contact actuation mechanism" (the current Model

NT 65A2 is provided with the contact actuation mechanism only). The grip tape wound around the handle of the

body was changed to the grip rubber that is common to the Model NR 83A2. The new Model NT 65A3 has the

same construction as the current Model NT 65A2 including the well-reputed tool-less clogged nail release

mechanism, driving force, response and balance.

3. APPLICATIONS

Finish-nailing of door casings, window casings and similar frame assemblies.

Fastening of drawer bottoms and similar assembly work in the construction of various cabinets and cases.

4. SELLING POINTS

Rapid driving and
quick response

Equipped with a rubber grip

With "single actuation/
contact actuation" selector

Содержание NT 65A3














































Результаты поиска

Содержание NT 65A3

Отзывы:

Похожие инструкции для NT 65A3

Бренды по названию

Популярные бренды

Hitachi NT 65A3, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание NT 65A3

Отзывы:

Похожие инструкции для NT 65A3

Бренды по названию

Популярные бренды