Hitachi NT 65A3 Скачать руководство пользователя страница 33

Страница: 33 / 45

--- 30 ---

(a) Disassembly (Refer to Fig. 17.)

Disassemble the Nose Ass'y [22], the Magazine Ass'y [63] and the related parts in a single body as

described in pararaph 10-1-(1).

Extract the Roll Pin D3 x 30 [38] with a 3-mm dia. roll pin remover, and take out Plunger (B) [52], Plunger

(B) Spring [51], Washer M5 [50], Trigger [59], and the Trigger Plunger [58].

Insert a flat-blade screwdriver (or J-125 valve bushing spanner) into the groove on the Trigger Valve

Bushing [57] and, being very careful not to damage or deform the groove portion, turn it counterclockwise to

loosen it. After the Trigger Valve Bushing [57] has been removed, the Valve Packing [53] and Urethane Ball

safely removed with the J-125 valve bushing spanner.)

After removing the Trigger Valve Bushing [57], pull down strongly on the Valve Bushing [45] to remove the

Valve Bushing [45], Valve Sleeve [47], Plunger (A) [42], and the Plunger Spring [41].

Remove the Plunger O-ring [49] inside the Valve Bushing [45] and the two O-rings (P-9) [46] inside the

Valve Sleeve [47] by means of a setting pin with a rounded tip (Fig. 18).

(b) Reassembly

Reassembly can be accomplished by following the disassembly procedures in reverse. However, special

attention should be given to the following items.

Plunger Spring [41] and Plunger (B) Spring [51] are small and apt to be twisted and lost. Be careful when

handling them.

To prevent the two O-rings (I.D 10.7) [44] on the outside of the Valve Bushing [45] from being damaged

when inserted into the body, carefully apply grease to the body hole and the outer circumference of the

O-rings prior to assembly.

* If damaged O-rings (I.D 10.7) [44] are mounted, a malfunction may occur. Be careful when handling them.

The Plunger O-ring [49] inside the Valve Bushing [45] is small and hard to mount a little. Be careful not to

lose the O-ring when handling.

Mount the Valve Bushing [45] again facing the four 2.5-mm dia. holes at its center to the Body Ass'y [19]

side (Fig. 19).

10-3. Disassembly and Reassembly of the Control Valve Section

Tools required

3 mm dia. (0.118") roll pin remover

Flat-blade screwdriver [J-125 valve bushing spanner (special repair tool, Part No. 97893) is recommended

in place of a screwdriver.]

Setting pin (with a rounded tip)

Содержание NT 65A3














































Результаты поиска

Содержание NT 65A3

Отзывы:

Похожие инструкции для NT 65A3

Бренды по названию

Популярные бренды

Hitachi NT 65A3, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание NT 65A3

Отзывы:

Похожие инструкции для NT 65A3

Бренды по названию

Популярные бренды