Hitachi NT 65A3 Скачать руководство пользователя страница 9

Страница: 9 / 45

--- 6 ---

7. PRECAUTIONS IN SALES PROMOTION

In the interest of promoting the safest and most efficient use of the Model NT 65A3 Nailer by all of our customers,

it is very important that at the time of sale, the salesperson carefully ensures that the buyer seriously recognizes

the importance of the contents of the Handling Instructions, and fully understands the meaning of the precautions

listed on the Warning Label attached to each tool.

7-1. Handling Instructions

Although every effort is made in each step of design, manufacture, and inspection to provide protection against

safety hazards, the dangers inherent in the use of any pneumatic tool cannot be completely eliminated.

Accordingly, general precautions and suggestions for the use of pneumatic tools, and specific precautions and

suggestions for the use of the pneumatic nailer are listed in the Handling Instructions to enhance the safe, efficient

use of the tool by the customer.

Salespersons must be thoroughly familiar with the contents of the Handling Instructions to be able to offer

appropriate guidance to the customers during sales promotion.

7-2. Warning Label

Each Model NT 65A3 unit is provided with a Warning Label (illustrated below) which lists basic safety precautions

in its use. Carefully ensure that the customers fully understand and follow these precautions before using the

tool.

Содержание NT 65A3














































Результаты поиска

Содержание NT 65A3

Отзывы:

Похожие инструкции для NT 65A3

Бренды по названию

Популярные бренды

Hitachi NT 65A3, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание NT 65A3

Отзывы:

Похожие инструкции для NT 65A3

Бренды по названию

Популярные бренды