Hitachi NT 65A3 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 45

background image

--- 20 ---

Remove the abnormal nails
and load the magazine with
normal nails.

<

Magazine>

Nail groove of the magazine
is abnormal (too wide, too
narrow, deformed or
damaged).

<Nails>

Magazine is not loaded with
specified genuine nails.

Problem

Possible cause

Inspection method

Remedy

Repair or replace the
defective part.

9. TROUBLESHOOTING GUIDE

9-1. Troubleshooting and Correction

1) Nails cannot
be driven.

Check if the magazine is
normally loaded with
specified nails.

Check if nails (one strip)
move smoothly in the
magazine.

Check if the nail feeder
operates smoothly in the
magazine.

Use specified nails.

Remove the adhesive
fragments and apply oil to
the nail feeder, ribbon spring
and the nail rail.

Magazine is loaded with
abnormal nails (bent nails,
large or small head nails,
abnormal collation, etc.).

Magazine is abnormal
(deformed or damaged).

Nail feeder is abnormal
(deformed or damaged).

Ribbon sping is abnormal
(deformed or damaged).

Magazine cover is abnormal
(deformed, damaged or
fatigued).

Check the nail feeding
section for abnormal
conditions (burrs, fatigued,
deformed or damaged).

<

Nose>

Nail inlet groove of the nose
is abnormal (deformed,
burrs or damaged).

Repair or replace the
defective part.

Remove the adhesive
fragments.

Adhesive fragments are in
the nail inlet groove.

Check if nails (one strip)
are fed smoothly into the
nail injection port of the
nose.

Collating band is abnormally
adhesive.

«
...
21
22
23
24
25
...
»

Содержание NT 65A3














































Отзывы:

Нет отзывов

Похожие инструкции для NT 65A3

Бренд: Bosch Страницы: 13

Бренд: Costway Страницы: 6

Бренд: Poniie Страницы: 5

Бренд: RIDGID Страницы: 36

Бренд: Parkside Страницы: 22

Бренд: Campbell Hausfeld Страницы: 12

Бренд: Campbell Hausfeld Страницы: 12

FinishPro XtremePro 25 XP

Бренд: Senco Страницы: 2

Бренд: YATO Страницы: 88

Бренд: Milwaukee Страницы: 20

Бренд: Rapid Страницы: 4

Бренд: Omer Страницы: 2

Бренд: Hitachi Страницы: 46

Бренд: Omer Страницы: 3

Бренд: Grizzly Страницы: 16

Бренд: Senco Страницы: 2

Бренд: Senco Страницы: 8

Бренд: Senco Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды